Best Bearing Puller Set with Case (2026)
Bearing puller sets with cases, compared by stated capacity, jaw and collet size, piece count and warranty.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallDAYUAN 14Pc Separator9.6/10View on Amazon - 2
Best CaseDAYUAN 12Pc Separator9.6/10View on Amazon - 3
Best for Blind BearingsLainKeen Blind Puller9.5/10View on Amazon - 4
Best 3-Jaw PickAcymner 3 Jaw Puller9.4/10View on Amazon
A wheel bearing that refuses to move can turn a brake job into a long afternoon in the garage. The bearing sits tight on its shaft, the usual pullers slip off, and the job stalls. A best bearing puller set with case keeps the jaws, legs, forcing screw and separators together in a case, so the right piece is at hand when the bearing needs to come off.
GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall DAYUAN 14Pc Separator: 5 ton capacity, 2 in and 3 in separators, 4 sets of legs and a blow-molded case, with a 1 year warranty. Check price on Amazon
- Best Case DAYUAN 12Pc Separator: The same 5 ton separator job with a case sized 15 by 9.7 by 2 in, handle and latches, and a 1 year warranty. Check price on Amazon
- Best for Blind Bearings LainKeen Blind Puller: 8 collets from 8 to 32 mm with a slide hammer and a blow-molded case for internal bearings. Check price on Amazon
- Best 3-Jaw Pick Acymner 3 Jaw Puller: Even pressure on sleeve-type bearings from 0.7 to 1.5 in, with forged and heat-treated jaws. Check price on Amazon
Picks for the garage
DAYUAN 14Pcs Bearing Separator Puller Set
A 14 piece separator set with 2 in and 3 in separators, a 5 ton capacity, 4 sets of push-puller legs, a 6 in yoke and a blow-molded case.
Pros
- 5 ton capacity for heavy pulling jobs
- 2 in and 3 in separators cover a range of bearing sizes
- 4 sets of push-puller legs with 4 in and 5 in extension legs
- Blow-molded case keeps every piece together
Cons
- No safety listing stated
- Case size not stated
- No slide hammer, so blind-hole bearings need a different set
- Spec table says NumberOfItems 1 while the title says 14 pieces
DAYUAN 12pcs Bearing Separator Puller Set
A 12 piece separator set with 2 in and 3 in separators, a 5 ton capacity, 4 in and 5 in legs, and a blow-molded case sized 15 by 9.7 by 2 in.
Pros
- 5 ton capacity, stated as 4.5 MT in the bullets
- Case size stated: 15 by 9.7 by 2 in with handle and latches
- 2 in and 3 in separators with 4 in and 5 in legs
- Drop forged and heat treated, black oxide finish
Cons
- No safety listing stated
- No slide hammer for blind-hole bearings
- Fewer pieces than the 14 piece DAYUAN set
- No yoke listed in the contents
OMT Bearing Puller Set, Bearing Splitter Tool Kit
A 14 piece splitter kit with 2 in and 3 in jaws, a 5 ton capacity, a 6 in yoke and extension screws, in heat-treated Cr-V steel with a black oxide finish.
Pros
- 5 ton capacity jaws for wheel hub and axle bearings
- 2 in and 3 in separator jaws with a knife-like taper
- Heat-treated Cr-V steel with black oxide finish
- Extension screws in 4-1/3 in and 5-1/3 in lengths reach tight spaces
Cons
- No case stated in the listing
- Spec table says NumberOfItems 1 while the title says 14 pieces
- No safety listing stated
- No slide hammer for blind-hole bearings
LainKeen 13pcs Blind Hole Collet Bearing Puller
A blind-hole collet set with 8 collets covering 8 to 32 mm, a slide hammer and a blow-molded case, for pulling internal bearings from motorcycles, cars and trucks.
Pros
- 8 collets cover blind holes from 8 to 32 mm
- Slide hammer for quick pulls, countersink hammer for tighter work
- Blow-molded case organizes the pieces
- High quality alloy steel per the listing
Cons
- Title says 13 pieces while bullets and spec table say 12
- No capacity in tons stated
- No safety listing stated
- Collets only fit blind holes from 8 to 32 mm
Acymner 3 Jaw Inner Bearing Puller Set
A 3-jaw inner bearing puller for sleeve-type bearings from 0.7 to 1.5 in, in heat-treated carbon steel with a black oxide finish.
Pros
- 3-jaw design spreads pressure evenly
- Fits sleeve-type bearings from 0.7 to 1.5 in
- Forged and heat-treated jaws
- Suits flywheels, motorcycle and bicycle wheels, pumps and generators
Cons
- 6 month warranty, shorter than the 1 year terms here
- No case stated
- No capacity in tons stated
- No safety listing stated
Compared on paper
| Model | Shop Score | Capacity | Jaw / collet range | Pieces | Case | Warranty |
|---|---|---|---|---|---|---|
| DAYUAN 14Pc Separator | 9.6/10 | 5 ton | 2 in and 3 in separators | 14 | Blow-molded case | 1 year |
| DAYUAN 12Pc Separator | 9.6/10 | 5 ton | 2 in and 3 in separators | 12 | Blow-molded case | 1 year |
| OMT Bearing Splitter | 9.5/10 | 5 ton | 2 in and 3 in jaws | 14 | Not stated | 1 year |
| LainKeen Blind Puller | 9.5/10 | Not stated | 8 to 32 mm collets | 12 | Blow-molded case | 1 year |
| Acymner 3 Jaw Puller | 9.4/10 | Not stated | 0.7 to 1.5 in | 1 | Not stated | 6 months |
Capacity is the ton figure each listing states. Specifications are manufacturer rated, as published on each listing and collected 4 November 2026.
How the points were given
Each set is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A stated warranty term earns warranty points; no set here states a safety listing, so none earns safety points.
| Product | Shop Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| DAYUAN 14Pc Separator | 9.6 | 32 | 22 | 21 | 0 | 3 |
| DAYUAN 12Pc Separator | 9.6 | 30 | 21 | 21 | 0 | 3 |
| OMT Bearing Splitter | 9.5 | 29 | 21 | 20 | 0 | 3 |
| LainKeen Blind Puller | 9.5 | 28 | 20 | 20 | 0 | 3 |
| Acymner 3 Jaw Puller | 9.4 | 27 | 20 | 19 | 0 | 2 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.
What the listings tell you
This guide covers 5 bearing puller listings. All 5 state a warranty term: 4 give 1 year and 1 gives 6 months. 3 state a 5 ton capacity, and 2 of those are DAYUAN separator sets. 1 is a blind-hole collet kit with a slide hammer, and 1 is a 3-jaw inner puller. 3 state a blow-molded case; the OMT and Acymner listings state no case. 2 listings disagree on piece count: LainKeen says 13 in the title and 12 in the bullets, and OMT says 1 in the spec table and 14 in the title.
Buying guide: the best bearing puller set with case
Capacity in tons
3 of the 5 sets state a 5 ton capacity for wheel hub and axle bearings. The LainKeen and Acymner listings state no capacity, so compare the stated figure with the bearing in front of you before ordering.
Separator jaws or collets
Separator jaws sit behind a bearing on a shaft and pull it off; the sets here offer 2 in and 3 in jaws. Collets expand inside a blind hole instead, and the LainKeen set covers 8 to 32 mm.
Slide hammer or forcing screw
The LainKeen set pulls with a slide hammer: lock the collet in the inner race and pull the weight back. The separator sets use a forcing screw: the DAYUAN sets use a 6-1/4 in screw, the OMT set a 7-1/5 in screw. For tighter work the LainKeen listing also mentions a countersink hammer that tightens slowly.
Count the pieces
A 14 piece set lists 4 sets of legs, 2 separators, a yoke and a forcing screw; a 12 piece set lists 4 in and 5 in legs with no yoke. Read the contents list, not the headline count: LainKeen says 13 in the title and 12 in the bullets.
The case
3 of the 5 sets state a blow-molded case, and the DAYUAN 12 piece case is the only one with a stated size: 15 by 9.7 by 2 in, with a handle and latches. Measure the shelf before ordering: the OMT and Acymner listings state no case at all.
If this is a first bearing job, the best bearing puller for beginners roundup covers starter sets.
Use rated jack stands on solid ground, wear eye protection with power and air tools, keep fuel-burning equipment out of a closed garage, and follow the manual for every tool. Read our Safety Disclaimer.
Garage Fit Check
- Shelf space: the DAYUAN 12 piece case measures 15 by 9.7 by 2 in; the other cased sets state no case size.
- Jaw size: match the bearing to the 2 in and 3 in separators, the 8 to 32 mm collets, or the 0.7 to 1.5 in 3-jaw range.
- Capacity: 3 sets state a 5 ton capacity; the LainKeen and Acymner listings state no capacity figure.
- Storage: a blow-molded case keeps legs, screws and separators together; the OMT and Acymner listings state no case.
FAQ: garage tools
How do I use a bearing puller set?
Fit the separator jaws behind the bearing or the collet inside the inner race, connect the legs and cross bar, then turn the forcing screw to draw the bearing off the shaft. With a slide hammer set, lock the collet and pull the weight back.
How does a bearing puller work?
The jaws or collet grip the bearing, and the forcing screw pushes against the shaft while the jaws draw the bearing off. A slide hammer works by impact: the weight slides back and knocks the bearing out of a blind hole.
What size bearing puller do I need?
Match the tool to the bearing: 2 in and 3 in separators fit bearings those jaws can sit behind, 8 to 32 mm collets fit blind holes in that range, and the 3-jaw puller fits sleeve-type bearings from 0.7 to 1.5 in. Measure the bearing before ordering.
Do these bearing puller sets come with a case?
3 of the 5 sets state a blow-molded case: both DAYUAN sets and the LainKeen set. The OMT and Acymner listings state no case, so plan separate storage. The DAYUAN 12 piece case is the only one with a stated size: 15 by 9.7 by 2 in.
Related: the best bearing puller for beginners, the best bushing press tool, the best ball joint press kit for beginners, the best valve spring compressor for beginners, the best tie rod end separator for beginners and the engine and shop equipment hub.
