Best Brass Punch Set (2026): 4 Picks for Pins, Alignment and Drift Work
Four brass punch sets for pin removal and alignment, compared on pin sizes, length, handles and the warranty each listing states.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallPerformance Tool W7599.6/10View on Amazon - 2
Most PiecesSWANLAKE 8-Piece9.5/10View on Amazon - 3
Best Small SizesOtis Pro+ FG-9359.5/10View on Amazon - 4
Largest SizesBRSUNAVOM 5-Piece9.4/10View on Amazon
A roll pin sits flush in a hinge, stuck fast after years of road grime, and a steel punch would scar the pin and the part around it. The best brass punch set gives a home garage a softer striking tool: brass that moves the pin without marring the metal it touches. This roundup compares four sets on the pin sizes, the length, the handles and the warranty each listing states.
GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Performance Tool W759: 8 inch long punches with knurled steel handles, non-sparking heads and a lifetime warranty. Check price on Amazon
- Most Pieces SWANLAKE 8-Piece: 8 punches from 1/8 inch to 5/16 inch in a green storage pouch. Check price on Amazon
- Best Small Sizes Otis Pro+ FG-935: Hex machined punches from 3/32 inch to 1/4 inch, machined in the USA. Check price on Amazon
- Largest Sizes BRSUNAVOM 5-Piece: Drift punches from 1/4 inch to 3/4 inch with knurled grips for automotive work. Check price on Amazon
Picks for the garage
Performance Tool W759 5-Piece 8 in. Long Brass Pin
A 5 piece set of 8 inch long brass pin punches with knurled steel handles and non-sparking heads, carrying the only stated lifetime warranty here.
Pros
- 8 inch long punches reach deeply set pins
- Knurled steel handles for grip and long life
- Non-sparking soft metal striking heads
- Lifetime warranty stated, not covering abuse
Cons
- One bullet lists a lift range for vehicles, which belongs to a jack listing
- No storage case or pouch stated
- Pin sizes stop at 3/8 inch, below the largest drift sizes here
- 1.2 pound weight, the heaviest stated here
SWANLAKE 8-Piece Brass Punch Set
An 8 piece brass punch set in sizes from 1/8 inch to 5/16 inch, with each punch approximately 3.15 inches long and a green storage pouch.
Pros
- 8 punches, the most pieces here
- Sizes from 1/8 inch to 5/16 inch for common pin work
- Solid brass, made to prevent surface damage
- Green storage pouch keeps the set organized
Cons
- No warranty term stated in the listing
- No item weight stated in the listing
- No handle detail stated
- Punches are short at approximately 3.15 inches for deep pins
Otis Technology Pro+ 5 Piece Brass Punch Set
A 5 piece hex machined brass punch set in sizes from 3/32 inch to 1/4 inch, machined in the USA with a chamfered striking surface.
Pros
- Smallest pin size here at 3/32 inch
- Hex machined with a chamfered striking surface
- Corrosion-resistant brass, machined in the USA
- 0.551155655 pound item weight stated
Cons
- Warranty field reads No Nonsense with no term stated
- No safety listing stated
- Product dimensions of 1.0 by 1.0 by 1.0 inches do not match a punch set
- No punch length stated
5-Piece Brass Drift Punch Set, 1/4, 3/8, 1/2, 5/8
A 5 piece brass drift punch set in sizes from 1/4 inch to 3/4 inch with knurled grips, made for automotive, motorcycle and workshop repair.
Pros
- Largest pin sizes here, from 1/4 inch to 3/4 inch
- Knurled grip for control during repeated hammering
- Brass helps reduce scratching and marring on steel parts
- Stated for automotive, motorcycle and workshop repair
Cons
- No warranty term stated in the listing
- No item weight stated in the listing
- No product dimensions stated
- No punch length stated
Compared on paper
| Model | Shop Score | Pieces | Pin sizes | Length | Handle | Warranty |
|---|---|---|---|---|---|---|
| Performance Tool W759 | 9.6/10 | 5 | 1/8 to 3/8 in | 8 in | Knurled steel | Lifetime |
| SWANLAKE 8-Piece | 9.5/10 | 8 | 1/8 to 5/16 in | 3.15 in | Not stated | Not stated |
| Otis Pro+ FG-935 | 9.5/10 | 5 | 3/32 to 1/4 in | Not stated | Hex machined | No Nonsense |
| BRSUNAVOM 5-Piece | 9.4/10 | 5 | 1/4 to 3/4 in | Not stated | Knurled grip | Not stated |
Specifications are manufacturer rated, as published on each listing and collected 2 November 2026.
How the points were given
Each set is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. None states a safety listing, so every set here scores zero on that criterion, and the ranking comes from the other four criteria.
| Product | Shop Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Performance Tool W759 | 9.6 | 30 | 21 | 21 | 0 | 4 |
| SWANLAKE 8-Piece | 9.5 | 29 | 21 | 21 | 0 | 0 |
| Otis Pro+ FG-935 | 9.5 | 29 | 21 | 20 | 0 | 0 |
| BRSUNAVOM 5-Piece | 9.4 | 28 | 20 | 20 | 0 | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.
What the listings tell you
Four listings were compared. One states a lifetime warranty, one states a warranty description with no term, and the other listings state no warranty term. None states a safety listing. Two listings state an item weight, and three state product dimensions.
Buying guide: choosing the best brass punch set
Pin sizes
Size range decides which pins a set can drive. SWANLAKE covers 1/8 inch to 5/16 inch in 8 punches, Performance Tool covers 1/8 inch to 3/8 inch in 5 punches, Otis covers 3/32 inch to 1/4 inch in 5 punches, and BRSUNAVOM covers 1/4 inch to 3/4 inch in 5 drift punches. The Otis set covers the smallest pins at 3/32 inch, and the BRSUNAVOM set covers the largest at 3/4 inch. Match the range to the pins on your cars and machines before ordering.
Length and reach
Length decides whether a punch can reach a pin set deep in an assembly. The Performance Tool punches are 8 inches long, made to reach deeply set pins in obstructed areas. The SWANLAKE punches measure approximately 3.15 inches in length, built for control in tight spaces. Otis and BRSUNAVOM state no punch length, so compare those sets on sizes and handles instead.
Handles and grip
Knurled handles keep a punch from turning in the hand under the hammer. Performance Tool uses knurled steel handles, BRSUNAVOM uses a knurled grip section on each punch, and Otis uses hex machined bodies with a chamfered striking surface. SWANLAKE states no handle detail, only solid brass punches in a pouch. A chamfered striking surface reduces burring, per the Otis listing.
Brass and non-marring work
Brass is softer than steel, so a brass punch moves a pin without scarring the parts around it. SWANLAKE states solid brass punches made to prevent surface damage on delicate or finished materials. BRSUNAVOM states brass helps reduce scratching and marring on steel components while transferring hammer force. Performance Tool states non-sparking soft metal striking heads, and Otis states corrosion-resistant brass machined in the USA.
Use rated jack stands on solid ground, wear eye protection with power and air tools, keep fuel-burning equipment out of a closed garage, and follow the manual for every tool. Read our Safety Disclaimer.
Garage Fit Check
- Check the pin sizes against the pins on your cars and machines before the first job.
- The Performance Tool punches are 8 inches long, so check the storage spot fits them before ordering.
- Keep the SWANLAKE punches in the green storage pouch so the 8 sizes stay together.
- Check the striking faces for burring after heavy use, since the Otis listing notes a chamfered striking surface reduces burring.
FAQ: garage tools
What is a brass punch set used for?
A brass punch drives pins out of hinges, shafts and assemblies, and aligns holes during reassembly. Brass is softer than steel, so it moves pins without scarring the parts around them. The sets here cover pin removal, hole alignment and light repair work.
What pin sizes do I need?
The sets here cover 3/32 inch to 3/4 inch between them. Otis covers the smallest pins at 3/32 inch to 1/4 inch, SWANLAKE and Performance Tool cover the middle at 1/8 inch to 5/16 inch and 1/8 inch to 3/8 inch, and BRSUNAVOM covers the largest at 1/4 inch to 3/4 inch. Match the range to the pins you work with most.
Why use brass instead of steel punches?
Brass is softer than steel, so it is less likely to scar or deform the parts it strikes. SWANLAKE states its punches prevent surface damage on delicate or finished materials, and BRSUNAVOM states brass helps reduce scratching and marring on steel components. Performance Tool adds non-sparking heads for work where sparks are a concern.
How long should a brass punch be?
The Performance Tool punches are 8 inches long for deeply set pins in obstructed areas, and the SWANLAKE punches are approximately 3.15 inches long for control in tight spaces. Otis and BRSUNAVOM state no punch length. Pick long punches for deep pins and short punches for tight spaces.
Do brass punch sets come with a warranty?
The Performance Tool set states a lifetime warranty that does not cover abuse. The Otis warranty field reads No Nonsense with no term stated, and the SWANLAKE and BRSUNAVOM listings state no warranty term. Check the spec table before ordering.
Related: the engine and shop equipment hub, brass punch vs steel punch, the best punch set for roll pins, the best transfer punch set for metal, and the best punch and block set.
