Best Tube Bender 3/4 (2026)
Lever, ratcheting, manual and spring tube benders for 3/4 in tube compared by bend range, dies, max bend and weight.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallImperial 364FHA129.7/10View on Amazon - 2
Best Ratcheting KitVEVOR Ratcheting Bender9.6/10View on Amazon - 3
Best for Steel PipeVEVOR Manual Bender9.6/10View on Amazon - 4
Best Spring SetEoppen Spring Kit9.5/10View on Amazon
A line for the garage air system has to turn a corner without kinking, and a kinked tube is a wasted length of copper. This guide to the best tube bender 3/4 compares lever, ratcheting, manual and spring benders that cover 3/4 in tube, so you can match the tool to the line you need to bend.
GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Imperial 364FHA12: Dedicated 3/4 in lever bender with angle markings, cushion grips and an open-side design. Check price on Amazon
- Best Ratcheting Kit VEVOR Ratcheting Bender: 7 dies from 1/4 to 7/8 in, forward and reverse bends, plus a pipe cutter and a case. Check price on Amazon
- Best for Steel Pipe VEVOR Manual Bender: 7 steel dies from 3/8 to 1 in with a heavy base for iron pipe under 0.08 in thick. Check price on Amazon
- Best Spring Set Eoppen Spring Kit: 5 spring benders from 1/4 to 3/4 in for thin-wall copper, brass and aluminum. Check price on Amazon
Picks for the garage
Imperial Tool 364FHA12 Lever Type Tube Bender
A lever tube bender for 3/4 in O.D. tubing, with integrated angle markings, cushion grip handles and an open-side design, listed at 7.78 pounds.
Pros
- Integrated markings show the angle of bend
- Cushion grip handles for less fatigue
- Bends to 180 degrees with no scoring or flattening
- Open-side design slips over the tube at any point
Cons
- Fits 3/4 in O.D. tubing only
- Annealed soft copper and aluminum only
- No warranty term is stated
- No safety listing is stated
VEVOR Pipe Tube Bender, 1/4"-7/8" O.D. Ratcheting
A ratcheting tube bender for 1/4 to 7/8 in O.D. pipe, with 7 dies, forward and reverse bending, a pipe cutter and a deburring tool, listed at 10.7 pounds.
Pros
- 7 dies from 1/4 to 7/8 in
- Forward and reverse bending for hard-to-reach areas
- Bearing-type pipe cutter and deburring tool included
- Portable tool case included
Cons
- Bends to 90 degrees only
- Soft copper and aluminum only
- No warranty term is stated
- No safety listing is stated
VEVOR Pipe Tube Bender, 3/8" to 1" Manual Pipe
A manual pipe tube bender for 3/8 to 1 in pipe, with 7 steel dies, bending radii from 50 to 113 mm, a heavy base and a long handle.
Pros
- 7 steel dies from 3/8 to 1 in
- Bends iron pipe under 0.08 in thick
- Heavy base for stability during use
- Long handle with an ergonomic design
Cons
- Round stock only
- No weight is stated
- No warranty term is stated
- No safety listing is stated
Eoppen Spring Tubing Benders Kit 1/4, 3/8, 1/2
A set of 5 spring tube benders for 1/4, 3/8, 1/2, 5/8 and 3/4 in tubing, in spring steel with a galvanized surface, 13.7 inches long.
Pros
- 5 sizes from 1/4 to 3/4 in
- Bends to 180 degrees without curling or collapsing the tube
- Fits copper, brass, aluminum and thin steel tube
- 13.7 inch length suits most pipe sizes
Cons
- Spec table lists NumberOfItems as 1 for a 5-piece set
- Thin-walled tube only
- No warranty term is stated
- No safety listing is stated
Tnisesm Spring Tube Bender Set 1/4'', 3/8''
A set of 5 spring tube benders for 1/4, 3/8, 1/2, 5/8 and 3/4 in tubing, in oil-quenched and tempered spring steel, 13.7 inches long.
Pros
- 5 sizes from 1/4 to 3/4 in
- Bends to 180 degrees without curling or collapsing the tube
- Fits copper, aluminum and thin-wall steel tube
- Galvanized surface, for indoor and outdoor use
Cons
- Spec table lists NumberOfItems as 1 for a 5-piece set
- No weight is stated
- No warranty term is stated
- No safety listing is stated
Compared on paper
| Model | Shop Score | Type | Bend range | Dies | Max bend | Weight | Warranty |
|---|---|---|---|---|---|---|---|
| Imperial 364FHA12 | 9.7/10 | Lever | 3/4 in O.D. | Single size | 180 degrees | 7.78 lb | Not stated |
| VEVOR Ratcheting Bender | 9.6/10 | Ratcheting | 1/4 to 7/8 in | 7 | 90 degrees | 10.7 lb | Not stated |
| VEVOR Manual Bender | 9.6/10 | Manual | 3/8 to 1 in | 7 | Not stated | Not stated | Not stated |
| Eoppen Spring Kit | 9.5/10 | Spring | 1/4 to 3/4 in | 5 | 180 degrees | 2.44933573082 lb | Not stated |
| Tnisesm Spring Set | 9.5/10 | Spring | 1/4 to 3/4 in | 5 | 180 degrees | Not stated | Not stated |
Specifications are manufacturer rated, as published on each listing and collected 6 November 2026. Where a listing contradicts itself, both figures are shown.
How the points were given
Each bender is scored on performance, build, value, safety and warranty, using only what the listing publishes. None states a safety listing or a warranty term, so all score zero on safety and warranty.
| Product | Shop Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Imperial 364FHA12 | 9.7 | 32 | 22 | 20 | n/a | 0 |
| VEVOR Ratcheting Bender | 9.6 | 30 | 21 | 21 | n/a | 0 |
| VEVOR Manual Bender | 9.6 | 29 | 21 | 20 | n/a | 0 |
| Eoppen Spring Kit | 9.5 | 28 | 19 | 20 | n/a | 0 |
| Tnisesm Spring Set | 9.5 | 27 | 19 | 19 | n/a | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score. Safety counts only for powered gear or where the listing states safety features; where it does not apply, the score is taken over the remaining 90 points.
What the listings tell you
The listings split into spring sets, a lever bender, a ratcheting bender and a manual bender. The spring sets and the lever bender state bends up to 180 degrees, while the ratcheting bender states up to 90 degrees and the manual bender states no bend angle. Dies run 1/4 to 7/8 in on the ratcheting bender and 3/8 to 1 in on the manual bender, and the spring sets cover 1/4 to 3/4 in without dies. Some listings state a weight and some do not, and no listing states a warranty term.
Buying guide: the best tube bender 3/4
Spring, lever, ratcheting or manual
Spring benders slide over thin-wall tube and bend it by hand to 180 degrees, which suits copper, brass, aluminum and thin steel lines. A lever bender fits a single size, here 3/4 in, with markings that show the angle as you bend. A ratcheting bender swaps dies across sizes and bends forward and reverse, while a manual bender with a heavy base suits steel pipe in a repair shop.
Dies and bend range
Match the die to the tube: the ratcheting bender covers 1/4 to 7/8 in, the manual bender covers 3/8 to 1 in, and the spring sets cover 1/4 to 3/4 in. A 3/4 in die fits 3/4 in tube, and the manual bender is the only listing here that reaches 1 in tube.
Max bend angle
The spring sets and the lever bender state bends up to 180 degrees, while the ratcheting bender states up to 90 degrees. The manual bender states no bend angle, so check the listing before planning a tight return bend.
Weight and storage
The ratcheting bender lists 10.7 pounds with a portable tool case, and the lever bender lists 7.78 pounds. The manual bender measures 35.4 by 8.6 by 5.0 inches with no weight stated, so plan bench space for it. The spring sets run 13.7 inches long.
Use rated jack stands on solid ground, wear eye protection with power and air tools, keep fuel-burning equipment out of a closed garage, and follow the manual for every tool. Read our Safety Disclaimer.
Garage Fit Check
- The manual bender measures 35.4 by 8.6 by 5.0 inches, so check bench space before the first job.
- The ratcheting bender measures 17.7 by 13.0 by 3.0 inches and comes with a portable tool case.
- The lever bender measures 32.6 by 5.9 by 4.1 inches and lists 7.78 pounds.
- The spring sets run 13.7 inches long.
- Check the die size against the tube before bending: the dies run 1/4 to 7/8 in on the ratcheting bender and 3/8 to 1 in on the manual bender.
FAQ: garage tools
What size tube bender do I need for 3/4 in tube?
A bender with a 3/4 in die, or a lever bender built for 3/4 in tube. Each listing here covers 3/4 in tube: the lever bender is built for it, and the other listings include a 3/4 in die or spring.
Can a spring tube bender bend steel tube?
Thin steel only, according to the listings: the spring sets list thin steel and thin-wall steel tube. For iron pipe, the manual bender states iron pipe under 0.08 in thick.
What is the difference between a ratcheting bender and a lever bender?
The ratcheting bender swaps 7 dies from 1/4 to 7/8 in and bends forward and reverse to 90 degrees. The lever bender fits 3/4 in tube only, bends to 180 degrees and shows the angle on integrated markings.
Do tube benders work on 1 in tube?
The manual bender covers 3/8 to 1 in pipe, so it is the listing here that reaches 1 in. The ratcheting bender stops at 7/8 in, and the spring sets stop at 3/4 in.
Can I bend tube to 180 degrees?
Yes, with the spring sets or the lever bender, which state bends up to 180 degrees. The ratcheting bender states up to 90 degrees, and the manual bender states no bend angle.
Related: the best tube bender for aluminum, the best tube bender for stainless steel, the best brake pipe bender and the engine and shop equipment hub.
