Best Universal Floor Jack Rubber Pad (2026): 5 Picks Compared

A floor jack saddle is bare steel, and a pinch weld is a thin folded edge, so lifting without a pad in between is how paint gets scraped and rails get bent. The best universal floor jack rubber pad sits between the saddle and the lift point, spreads the load and grips the seam, and this guide compares the pads below by size, groove fit, capacity and pack count.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Picks for the garage

#	Product	Shop Score	Buy
1	Moibunka Universal Floor Jack Rubber Pad & Jack	9.7/10	Buy on Amazon
2	TONDA Floor Jack Pad, Pinch Weld Jack Adapter	9.7/10	Buy on Amazon
3	Universal Floor Jack Rubber Pad Jack Pad Adapter	9.6/10	Buy on Amazon
4	Yesland 6 Pack Universal Floor Jack Rubber Pad	9.6/10	Buy on Amazon
5	JUKFITA Floor Jack Rubber Pad	9.5/10	Buy on Amazon

1

Moibunka Universal Floor Jack Rubber Pad & Jack

Moibunka·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5 in universal floor jack rubber pad, 1.1 in thick, with a cross slot for pinch welds and a 3 ton maximum load.

Check price on Amazon

Pros

• 5 in diameter and 1.1 in thick
• Cross slot with a 0.7 in groove width and a 0.23 in groove depth
• 3 ton maximum load bearing
• 1 year warranty

Cons

• 1 pad in the pack
• Listing repeats the fitment warning
• Saddle size must be measured before purchase
• Weight appears only in the spec table

2

TONDA Floor Jack Pad, Pinch Weld Jack Adapter

TONDA·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 pack of 4.92 in floor jack rubber pads, 1.02 in thick, with slotted cross grooves for pinch welds and a waffle-textured top.

Check price on Amazon

Pros

• 2 pads in the pack
• 4.92 in diameter and 1.02 in thick
• Rated 2 to 3 tons
• Waffle-textured top for grip

Cons

• No warranty term stated
• No groove width or depth stated
• Weight figures in the listing do not agree
• Spec table lists 0 items against a 2 pack title

3

Universal Floor Jack Rubber Pad Jack Pad Adapter

GeeWatom·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4.92 in universal floor jack rubber pad, 1.02 in thick, with a cross slotted design for pinch welds and a 2 ton maximum load.

Check price on Amazon

Pros

• 4.92 in diameter and 1.02 in thick
• 2 ton maximum load bearing
• Cross slotted design for pinch welds
• 90 day warranty

Cons

• 1 pad in the pack
• 2 ton capacity is the lowest stated here
• Spec table lists an item weight that does not match a rubber pad of this size
• New rubber smell noted in the listing

4

Yesland 6 Pack Universal Floor Jack Rubber Pad

Yesland·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6 pack of square 3 in floor jack rubber pads, 1 in thick, each 150 g, with slotted grooves for pinch welds and frame rails.

Check price on Amazon

Pros

• 6 pads in the pack
• 3 in square and 1 in thick
• Each pad weighs 150 g
• Groove depth of 3/8 in

Cons

• No capacity stated
• No warranty term stated
• 3 in square size is smaller than the round pads here
• No separate groove width stated

5

JUKFITA Floor Jack Rubber Pad

JUKFITA·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4.92 in floor jack rubber pad, 0.98 in thick, with a slotted design for pinch welds and a non-slip hold on the jack.

Check price on Amazon

Pros

• 4.92 in diameter and 0.98 in thick
• Slotted design for weld points
• Non-slip hold on the jack
• Easy to install

Cons

• No capacity stated
• No warranty term stated
• No groove dimensions stated
• No weight stated

Compared on paper

Specs such as CFM, PSI and torque are the manufacturer’s ratings as listed, collected 2 November 2026. Where a listing contradicts itself, both figures are shown.

How the picks were scored

Each pad is scored on performance, build, value, safety and warranty, with the weights published on the How We Pick page. None states an ASME PASE listing, so all score 0 on safety, and 3 give no clear warranty term.

Shop Scores range from a low of 9.2 to a high of 9.8, with each tool positioned by its weighted points proportionally, and more points always yields a higher score. Where a tool neither runs on power nor lists a safety feature, safety shows n/a and the other 90 points decide.

What the listings tell you

5 pad listings were compared. 3 state a capacity, 2 state a warranty term, and all state a diameter and a thickness. 2 listings give groove dimensions, and 2 contradict themselves on weight or item count.

Buying guide: the best universal floor jack rubber pad for your garage

Size and saddle fit

Diameter is the first check: 3 listings give 4.92 in, 1 gives 5 in, and 1 gives a 3 in square pad. Thickness runs from 0.98 in to 1.1 in. Measure the saddle before buying, since a pad that overhangs the saddle can shift under load, and a pad smaller than the lift point leaves the seam unprotected.

Groove fit for pinch welds

The groove is what keeps the pad on the seam. Moibunka states a 0.7 in groove width with a 0.23 in groove depth, and Yesland lists its groove as 3/8 in by 3/8 in. The other 3 listings state a slotted or cross-groove design with no groove size, so compare the slot against the weld before the first lift.

Capacity

Stated capacities are 3 ton, 2 to 3 tons, and 2 ton. The other 2 listings state no capacity at all, so a pad with no stated rating should be matched to the smallest job in the garage, not the heaviest. Match the rating to the vehicle, and never guess at a rating the listing does not give.

Pack count

Pads sell as a 1 pack, a 2 pack, or a 6 pack. A 2 pack covers 2 lift points with a spare in the drawer, and a 6 pack covers every lift point with spares left over. A 1 pack suits a buyer who lifts at 1 point and already owns pads for the rest.

Rubber and grip

All 5 pads are rubber, and the listings describe hard rubber, heavy duty rubber, and durable rubber. Grip comes from texture: TONDA lists a waffle-textured top, Yesland lists an anti-slip surface, and the rest rely on the slot and the soft rubber face to hold position.

Jack safety

Never get under a vehicle supported by a jack alone. Use rated stands on solid, level ground, and lift only at the points shown in the owner’s manual. A rubber pad protects the seam and the paint, but it is not a stand, and it does not change the jack rating.

Garage Fit Check

• Measure the saddle before buying: pads here run from a 3 in square to 5 in across, with thicknesses from 0.98 in to 1.1 in.
• Check the groove against the pinch weld: 2 pads state groove dimensions, and the rest state a slotted design with no size given.
• Match the rating to the job: stated capacities run from 2 ton to 3 ton, and 2 pads state no capacity.
• Count the lift points before ordering: packs here are 1, 2, and 6 pads, and a spare pad in the drawer beats ordering again.
• No pad here needs power, air, or charging, and each pad stores flat in a drawer or on a shelf.

FAQ: garage tools

What do jack pads do?

A jack pad sits between the floor jack saddle and the vehicle’s lift point. It cushions the contact, spreads the load across the pad face, and keeps the steel saddle off painted metal and pinch welds.

What size floor jack rubber pad fits most jacks?

3 of the 5 listings give a 4.92 in diameter, 1 gives 5 in, and 1 gives a 3 in square pad, so a 4.92 in pad is the common size here. Measure the saddle before buying, since the listing for each pad asks for a fitment check.

Do rubber jack pads work with jack stands?

Yesland states that its pad can work with a jack stand as well as a floor jack. A pad is still not a stand: never get under a vehicle supported by a jack alone, and use rated stands on solid, level ground.

What is the groove in a jack pad for?

The groove lines up with the pinch weld so the seam sits inside the pad instead of against flat steel. Moibunka states a 0.7 in groove width and a 0.23 in groove depth, and Yesland lists its groove as 3/8 in by 3/8 in.

How much weight can a rubber jack pad hold?

Stated capacities here are 2 ton, 2 to 3 tons, and 3 ton. 2 listings state no capacity, so check the listing for the pad in hand and match the rating to the vehicle before lifting.

Related: the best 3 ton jack stands, the floor jack picks and the rubber vs aluminum jack pads comparison.