How to Get a Tire to Bead at Home
A tire bead seats when a sharp blast of air from a bead seater pushes the tire sidewall out onto the rim, and this guide walks through the setup, the blast and the checks that follow.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
RIXGWND Tire Bead Seater,3.2 Gal/12L Portable Tire9.6/10View on Amazon - 2
TOOLUXE 30007L Air Tire Sealer9.6/10View on Amazon - 3
higehio 5 Gallon 145PSI Air Tire Bead Seater9.6/10View on Amazon - 4
XtremepowerUS 5-Gallon Heavy Duty Tire Bead Seater9.6/10View on Amazon
A tire that has come off its rim will not hold air, and pumping through the valve stem often will not fix it. How to get a tire to bead is a matter of pushing the tire sidewall out against the rim in a sharp blast of air, so the bead catches and seals. A bead seater tank does that job: fill it from a shop compressor, set the barrel at the gap between tire and rim, and release the air. Once the bead pops on, inflate the tire through the valve stem and check for leaks.
GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.
Below: the checks, the seating steps, what to do when the bead will not seat, and the bead seaters that do the job.

RIXGWND Tire Bead Seater,3.2 Gal/12L Portable Tire
A 3.2-gallon steel bead seater rated at 145 PSI maximum, with an 87-116 PSI operating range, a gauge, a trigger and a safety valve.
Pros
- 3.2-gallon tank, compact handheld size
- 145 PSI maximum, 87-116 PSI operating range
- Trigger and non-slip grip, long duck-bill barrel
- 365-day warranty stated
Cons
- 3.2-gallon tank holds less air than the 5-gallon models
- 22.5 lb for the smallest tank
- Needs eye and ear protection before seating a tire
- Handheld use means holding the tank during the blast

TOOLUXE 30007L Air Tire Sealer
A 5-gallon steel bead seater rated at 145 PSI maximum, with an 87-116 PSI operating range, a gauge and an automatic safety valve.
Pros
- 5-gallon tank, 145 PSI maximum
- 87-116 PSI operating range, easy-to-read gauge
- CE approved all-steel tank, powder-coated finish
- Automatic safety valve releases excess air
Cons
- Fits tires up to 24.5 inches
- Needs a standard shop compressor to fill
- 22.0 lb tank to lift and carry
- No warranty term is stated

higehio 5 Gallon 145PSI Air Tire Bead Seater
A 5-gallon carbon steel bead seater rated at 145 PSI maximum, with an 87-116 PSI working pressure, a built-in gauge and an automatic safety valve.
Pros
- 5-gallon tank, 145 PSI maximum
- 2.5 mm carbon steel tank, powder finish
- 87-116 PSI working pressure, built-in gauge
- Automatic safety valve releases excess air
Cons
- 23.5 lb, the heaviest of the models with a stated weight
- Fits tires under 24.5 inches only
- Needs ear and eye protection before inflating
- No warranty term is stated

XtremepowerUS 5-Gallon Heavy Duty Tire Bead Seater
A 5-gallon carbon steel tire bead seater with a 145 psi rating, angled-lip threaded barrel, built-in carry handle and integrated pressure gauge.
Pros
- Large 5-gallon tank volume supplies high air volume
- 145 psi maximum pressure rating for stubborn beads
- Specially angled barrel lip stabilizes nozzle on the rim
- Includes a 60-day manufacturer warranty
Cons
- Short 60-day warranty term
- Weighs 25.8 pounds empty before filling with air
- Listing noise specification reads 120 dB
Check the tire and rim first
Look over the tire and rim first. Clean the bead area of dirt, rust and old sealant so the rubber sits flat. Look for cuts in the sidewall, cracks in the rim and any bend that stops the bead sealing. A damaged tire or bent rim may not seat, so take it to a tire shop. Wet the bead with soapy water.
How to get a tire to bead at home
Work through the steps in order, keeping clear of the tire.
- Fill the tank. Connect the bead seater to a shop compressor and fill it to the operating pressure the maker states, 87-116 PSI on the TOOLUXE, RIXGWND and higehio models below.
- Set the barrel. Put the barrel into the gap between tire and rim, with the lip aimed at the bead.
- Release the blast. Open the valve or press the trigger to send the stored air into the gap in a burst. The sidewall should jump out against the rim.
- Inflate through the valve. With the bead seated, connect an inflator to the valve stem and fill the tire.
- Check the seal. Brush soapy water around the rim edge and watch for bubbles. If air escapes, let the tire down and repeat the steps.
If the bead will not seat
When the bead stays loose after a blast, check the likely causes. Check that the tank is full, since a low tank gives a weak blast. Check that the barrel lip sits in the gap and points at the bead. Clean the bead seat and wet the bead. If the tire still will not seat, take the wheel to a tire shop: the bead or rim may be damaged.
The gear: bead seaters that seat the bead
The blast that seats the bead comes from a bead seater tank, so the four models below are the gear for the seating step. Each one stores air and releases it in a blast that pushes the sidewall onto the rim.
Stay safe while seating a bead
A bead seater releases a large volume of air in a short burst. Wear eye and ear protection before seating a tire, keep hands and face clear while the air is released, and never fill the tank past the operating pressure the maker states.
Wear eye protection with every air tool, use impact-rated sockets on impact wrenches, disconnect the air line before changing accessories, and finish lug nuts with a torque wrench to the vehicle's spec. See OSHA eye and face protection. Read our Safety Disclaimer.
FAQ: garage tools
Can I seat a tire bead without a bead seater?
A bead seater tank stores air and releases it in a sharp blast between the tire and the rim, which pushes the sidewall out onto the rim. A standard inflator fills the tire slowly, and the air often escapes before the bead can catch.
What pressure should a bead seater tank be filled to?
Fill the tank to the operating pressure the maker states: 87-116 PSI on the TOOLUXE, RIXGWND and higehio models below, with a 145 PSI maximum. Never fill past the operating pressure.
What size bead seater tank do I need?
The models below come in 5-gallon and 3.2-gallon tanks. A 5-gallon tank holds more air per blast; the 3.2-gallon model has the smallest tank here. The TOOLUXE model fits tires up to 24.5 inches, the higehio model under 24.5 inches.
Why will my tire bead not seat?
The usual causes are a tank below operating pressure, a barrel not set in the gap, dirt or rust on the bead seat, or a dry bead that will not slide. Clean the rim and try again. If the tire still will not seat, a tire shop should look at it.
Related: air compressors for the home garage, the best air compressor for air tools, what air compressor CFM means and the best tire bead sealer.




