Best Tool Box Drawer Liner 24 Inch Wide (2026)

Open a tool box drawer and the sockets have slid into a pile at the back again. A liner stops that slide, cushions the drawer and keeps the tools where you left them. This guide compares the picks to find the best tool box drawer liner 24 inch wide, by roll length, thickness, material, grip and warranty.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Picks for the garage

#	Product	Shop Score	Buy
1	ONREVA Tool Box Liner 24" Wide x 24 Ft	9.7/10	Buy on Amazon
2	ONREVA Tool Box Liner 24" Wide x 12 Ft	9.6/10	Buy on Amazon
3	Shelf Liner for ToolBox Drawer	9.6/10	Buy on Amazon
4	EPPCO Enterprises Tool Box Drawer Liner 24-inch	9.5/10	Buy on Amazon

1

ONREVA Tool Box Liner 24" Wide x 24 Ft

ONREVA·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 24 in wide by 24 ft long roll of 1/8 in thick PVC rubber liner, non-slip and trimmable, for tool chests, cabinets, workbenches and shelves.

Check price on Amazon

Pros

• 24 in wide by 24 ft long, the longest roll here
• 1/8 in thick PVC rubber for cushioning and vibration absorption
• Textured non-slip surface keeps tools from sliding
• Trims with scissors or a utility knife to fit many brands

Cons

• No warranty term is stated
• Black only
• Thicker than standard liners, so check drawer clearance
• Single roll, so measure your drawers before cutting

2

ONREVA Tool Box Liner 24" Wide x 12 Ft

ONREVA·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

The same 1/8 in thick PVC rubber liner in a 24 in wide by 12 ft long roll, non-slip and trimmable for smaller lining jobs.

Check price on Amazon

Pros

• 1/8 in thick PVC rubber, the same build as the longer roll
• Textured non-slip surface keeps tools in place
• Trims with scissors or a utility knife to fit
• 24 in wide by 12 ft long, enough for a smaller chest

Cons

• Shorter roll than the 24 ft pick
• No warranty term is stated
• Black only
• Fits the listed brands, so check yours before buying

3

Shelf Liner for ToolBox Drawer

PaBUSIOr·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 24 in by 68 in PVC mesh foam liner, 5 mm thick with convex grip dots, for tool box drawers and garage shelves.

Check price on Amazon

Pros

• 5 mm thick, the thickest liner here by a clear margin
• Convex dots on top grip tools and fragile items
• Strong tear resistance per the listing
• 24 in width suits deep tool chest drawers with room to trim

Cons

• Only 11.33 square feet, the smallest roll here by far
• Recommended uses list says sink, oddly
• No warranty term stated
• No safety listing stated

4

EPPCO Enterprises Tool Box Drawer Liner 24-inch

EPPCO·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 24 in wide by 72 in long non-slip drawer liner that wipes clean, with a 90 day warranty on material and workmanship.

Check price on Amazon

Pros

• 90 day warranty on material and workmanship
• Wipes clean and will not trap dirt and dust
• Fits most professional tool boxes with one cut
• Available in 24 by 30, 24 by 72, 18 by 72 and 12 by 72 sizes

Cons

• No thickness is stated on the listing
• No material is stated on the listing
• Shorter than the ONREVA rolls
• One mat per pack

Compared on paper

Specs such as CFM, PSI and torque are the manufacturer’s ratings as listed, collected 12 November 2026. Where a listing contradicts itself, both figures are shown.

How the points were given

Each liner is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. None states a safety listing, so all score zero on safety, and one gives a clear warranty term.

Shop Scores range from a low of 9.2 to a high of 9.8, with each tool positioned by its weighted points proportionally, and more points always yields a higher score. A tool with no power source and no listed safety feature has safety removed, and the score is taken over 90 points.

What the listings tell you

We read four liner listings. Two state 1/8 in thickness and PVC rubber construction. One states a 90 day warranty on material and workmanship. One listing gives only a title, with no bullets or spec table, so its card is short. The two ONREVA rolls share the same bullets and differ only in length, while the EPPCO mat is the only pick with a stated warranty.

Buying guide: best tool box drawer liner 24 inch wide

Width and length

Every pick here is 24 in wide. Length is where they differ: the rolls run 24 ft and 12 ft, and the mats run 72 in and 68 in. Measure your drawers, then pick the length that covers them. The ONREVA rolls trim to fit, while the EPPCO mat fits most professional tool boxes with one cut, so count the drawers before ordering and buy the length that covers them all.

Thickness

Two picks state a thickness of 1/8 in, and one states 5 mm of foam. The maker of the 1/8 in liner calls it thicker than standard liners, for cushioning and vibration absorption. The EPPCO pick states no thickness, so compare it on warranty and cleaning instead.

Material

Two picks state PVC rubber, and one states foam. The EPPCO pick states no material, so compare it on its warranty and easy-clean surface instead. PVC rubber is the stated material for the two longest picks, while the foam pick states shock absorbing as its job.

Non-slip grip

Every pick here states a non-slip surface. The ONREVA rolls add a textured surface that keeps tools, sockets, wrenches and accessories from sliding when drawers open and close. A liner that slides with the drawer is no help at all, so grip matters as much as thickness.

Trimming and fitment

The ONREVA rolls trim with scissors or a utility knife and fit toolboxes from brands such as Milwaukee, Dewalt, US General, Craftsman, Husky, Snap-on and Mac Tools. The EPPCO mat fits most professional tool boxes with one cut.

For the box that holds the drawers, see our tool box for pick up trucks picks.

Garage Fit Check

• Every pick here is 24 in wide, so check the drawer depth before you cut.
• The 24 ft roll covers the most drawers; the 12 ft roll and the 72 in mat cover fewer.
• The ONREVA rolls trim with scissors or a utility knife, so keep one at the bench when fitting.
• The EPPCO mat weighs 1.25 lb and wipes clean, while the PaBUSIOr foam mat is 5 mm thick.
• Store a spare roll flat on a shelf until the next drawer needs lining.

FAQ: garage tools

How thick should a tool box drawer liner be?

Two picks here state 1/8 in, and one states 5 mm of foam. The 1/8 in liner is described as thicker than standard liners, for cushioning and vibration absorption. Pick the thickness that suits the weight of the tools in the drawer.

Can I cut a tool box drawer liner to fit?

Yes. The ONREVA rolls trim with scissors or a utility knife, and the EPPCO mat fits most professional tool boxes with one cut. Measure the drawer first, then cut to fit. Cut the liner slightly long, then trim the edge for a snug fit.

How do I keep tools from sliding in a drawer?

Use a liner with a non-slip surface. Every pick here states one, and the ONREVA rolls add a textured surface that keeps tools, sockets, wrenches and accessories from sliding when drawers open and close.

Will a 24 in wide liner fit my tool box?

A 24 in wide liner covers a drawer of that depth, trimmed to size. The EPPCO mat is made to fit most professional tool boxes with one cut, and the ONREVA rolls fit the brands named on the listing. Measure the drawer before ordering. If the drawer is wider than the liner, one roll leaves a gap; if it is narrower, trim the liner to fit.

How do I clean a tool box drawer liner?

The EPPCO mat wipes clean and will not trap dirt and dust. The other listings state no cleaning method, so check the listing before buying. Lift the mat out, wipe it down and let it dry before putting it back.

Related: the best tool box for pick up trucks, best garage shelving under 100, the best tool backpack under 100, the best rolling tool bag under 150, the best magnetic tool holder under 25 and the best mechanic tool set under 150.