Best Pneumatic Rivet Gun for 3/32 to 1/4 Inch Rivets (2026)

A loose panel on a trailer or a rattling bracket under a fender calls for a blind rivet, and a pneumatic gun sets it in one pull instead of repeated squeezes on a hand tool. The best pneumatic rivet gun for 3/32 to 1/4 inch rivets is the one that covers the rivet sizes you actually set, with the pulling force and air supply to match, so this guide compares four air-powered guns by nose pieces, pulling force, air use and warranty, and says plainly what each listing does not state.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Picks for the garage

#	Product	Shop Score	Buy
1	DKwoeshg Pneumatic Rivet Gun	9.6/10	Buy on Amazon
2	Campbell Hausfeld TL053900 Pneumatic Pop Rivet	9.5/10	Buy on Amazon
3	Pneumatic Rivet Gun,Air Rivet Gun	9.5/10	Buy on Amazon
4	BORNTUN Air Rivet Gun 1/4 Inch Rivet Gun Heavy	9.2/10	Buy on Amazon

1

DKwoeshg Pneumatic Rivet Gun

DKwoeshg·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An air-powered rivet gun with 5 nosepieces from 3/32 to 1/4 inch, 1,870 lbf of pull and a mandrel collector.

Check price on Amazon

Pros

• Only pick here with a 1/4 inch nosepiece
• 1,870 lbf pull capacity with a 0.551 in stroke
• Mandrel collector included
• 1 year manufacturer warranty stated

Cons

• Average air use of 4 ft3/min is the highest here
• The spec table lists part number D100353 and model Z100146, so confirm the model when you order
• No dimensions or weight are stated on the listing
• No safety certification is stated

2

Campbell Hausfeld TL053900 Pneumatic Pop Rivet

Campbell Hausfeld·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An air-powered hydraulic rivet gun with 2,000 pounds of pulling force, 4 nose pieces and a 1 year limited warranty.

Check price on Amazon

Pros

• 2,000 pounds of pulling force, the highest here
• Uses only 0.2 CFM at 90 PSI
• Sets steel rivets up to 3/16 inch
• 1 year limited warranty stated, with dimensions listed

Cons

• No 1/4 inch nose piece, so it does not cover the full range in the keyword
• Needs a 2-gallon or larger compressor and a 1/4 inch hose
• No mandrel collector is listed
• No safety certification is stated

3

Pneumatic Rivet Gun,Air Rivet Gun

Vanwoke·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An air-hydraulic rivet gun with 1912.5 lbs of pulling force, 4 nose cones and 40 rivets in the box.

Check price on Amazon

Pros

• 1912.5 lbs of pulling force with an air-hydraulic drive
• 40 rivets included, 10 of each size
• Three-piece steel teeth for stainless steel nails
• 16 mm working stroke for different rivet lengths

Cons

• No 1/4 inch nose cone, so it does not cover the full range in the keyword
• The listing lists 4 nose cone sizes but says 3 rivet heads are included
• Warranty is only 1 month
• No safety certification is stated

4

BORNTUN Air Rivet Gun 1/4 Inch Rivet Gun Heavy

BORNTUN·9.2/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A heavy duty pneumatic hydraulic rivet tool whose title says 1/4 inch, but whose nosepieces stop at 3/16 inch.

Check price on Amazon

Pros

• Quick release air valve for fast cylinder return
• Pulls stainless steel rivets, per the listing
• Performs well at any angle, per the listing
• Sturdy and easy to put together, per the listing

Cons

• Title says 1/4 inch, but the nosepieces stop at 3/16 inch and the size field says 3/16 inch Blue
• No pulling force is stated
• No air pressure or air use is stated
• No warranty term is stated

Compared on paper

Every rating comes from the brand’s listing and is not a shop test (gathered 11 November 2026).

How the points were given

Each gun is scored out of 10 on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.

No score drops under 9.2 or climbs past 9.8; a tool’s place inside those bounds is set by its weighted point total.

What the listings tell you

This guide compares 4 air-powered rivet gun listings. Only 1 covers the full range in the keyword: the DKwoeshg lists 5 nosepieces from 3/32 to 1/4 inch. 2 listings state a warranty term of 1 year, 1 states 1 month, and 1 states no warranty term at all. Pulling force runs from 1,870 to 2,000 pounds on the 3 listings that state it.

Buying guide: best pneumatic rivet gun for 3/32 to 1/4 inch rivets

Rivet sizes: does it cover 1/4 inch?

Only the DKwoeshg lists a 1/4 inch nosepiece, with 5 nosepieces from 3/32 to 1/4 inch. The Campbell Hausfeld and Vanwoke guns top out at 3/16 inch, with 4 nose pieces or nose cones each. The BORNTUN title says 1/4 inch, but its nosepieces stop at 3/16 inch and its size field says 3/16 inch Blue. If you set 1/4 inch rivets, the DKwoeshg is the only pick here that lists one.

Pulling force

Pulling force is the number that decides whether a gun sets a rivet in one pull. The Campbell Hausfeld lists 2,000 pounds, the Vanwoke lists 1912.5 lbs, and the DKwoeshg lists 1,870 lbf. The BORNTUN listing states no pulling force at all, so there is nothing to compare it against. A higher figure helps with steel rivets and larger sizes, but the listing has to state it first.

Air supply: pressure and CFM

These guns run on shop air, so check the pressure and the air use against your compressor. The DKwoeshg lists an air pressure of 85 to 95 psi with an average air consumption of 4 ft3/min. The Campbell Hausfeld lists 0.2 CFM at 90 PSI and recommends a 2-gallon or larger compressor with clean, dry air at 90 PSI. The Vanwoke lists a working pressure of 0.6 to 0.8 MPa, which the listing also gives as 6 to 8 bar. The BORNTUN listing states no air pressure and no air use. See what CFM air tools need and what size air compressor you need for air tools before you buy.

Nose pieces, mandrel and warranty

Nose pieces decide which rivet sizes a gun sets, and the mandrel collector decides where the spent mandrels go. The DKwoeshg has 5 nosepieces and a mandrel collector, the Campbell Hausfeld has 4 nose pieces, the Vanwoke has 4 nose cones and 40 rivets in the box, and the BORNTUN lists 3 nosepieces. On warranty, the DKwoeshg states 1 year, the Campbell Hausfeld states 1 year limited, the Vanwoke states 1 month, and the BORNTUN states no warranty term at all.

After the rivets are set, a blind rivet removal tool takes out the ones that need replacing.

FAQ: garage tools

What size rivets does a pneumatic rivet gun set?

It depends on the nose pieces. The DKwoeshg lists 5 nosepieces from 3/32 to 1/4 inch. The Campbell Hausfeld and Vanwoke guns list 4 nose pieces or nose cones from 3/32 to 3/16 inch. The BORNTUN lists 3 nosepieces from 1/8 to 3/16 inch, even though its title says 1/4 inch.

How much air does a pneumatic rivet gun need?

Check the listing for pressure and air use. The DKwoeshg lists 85 to 95 psi and an average of 4 ft3/min. The Campbell Hausfeld lists 0.2 CFM at 90 PSI and recommends a 2-gallon or larger compressor. The Vanwoke lists a working pressure of 0.6 to 0.8 MPa. The BORNTUN listing states no air figures.

Can a pneumatic rivet gun set stainless steel rivets?

Some can, per the listings. The Campbell Hausfeld sets steel rivets up to 3/16 inch. The Vanwoke has three-piece steel teeth for stainless steel nails. The BORNTUN listing says it can pull stainless steel rivets. Check the rivet material against the listing before you buy.

What is a mandrel collector?

It catches the spent mandrels as rivets are set, instead of letting them fall on the floor. The DKwoeshg listing includes a mandrel collector. The other 3 listings here do not list one.

Do I need a big compressor for a pneumatic rivet gun?

Not always. The Campbell Hausfeld listing recommends a 2-gallon or larger compressor, and the DKwoeshg lists an air pressure of 85 to 95 psi. Match the compressor to the pressure and air use your gun lists, and use clean, dry air as the Campbell Hausfeld listing recommends.

Related: the air tools hub, best pneumatic rivet gun, best pneumatic rivet tool, best rivet gun kit, best rivet gun for auto body work, hand vs pneumatic rivet gun, electric vs pneumatic rivet gun, and the blind rivet vs rivet nut guide.