Best Pressure Washer Nozzle Tip Holder (2026): 5 Wall-Mounted Picks

The wash is done, the car is drying, and the foam cannon is empty. The nozzle tips are scattered across the workbench, the foam cannon leans against the wall, and the wand rests in a corner where it can fall. A best pressure washer nozzle tip holder gives every tip, cannon and wand a fixed spot on the wall, so the next wash starts with the gear in hand instead of a hunt around the garage. This roundup compares the holders by what they hold, how they mount, and what they are made of.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Picks for the garage

#	Product	Shop Score	Buy
1	UNITEDPOWER Pressure Washer Gun Holder，Wall Mount	9.7/10	Buy on Amazon
2	4 Sets Foam Cannon Holder	9.6/10	Buy on Amazon
3	MYHLPER Pressure Washer Gun Holder,Foam Cannon	9.6/10	Buy on Amazon
4	RecDec 2 Pack Pressure Washer Nozzle Holder Holds	9.6/10	Buy on Amazon
5	10 Pack Pressure Washer Nozzle Rubber Grommet	9.5/10	Buy on Amazon

1

UNITEDPOWER Pressure Washer Gun Holder，Wall Mount

UNITEDPOWER·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A heavy metal wall rack with a powder coated finish that holds a pressure washer gun, foam cannon, nozzle and wand extension at once, with 1/4 inch quick connect male and female fittings.

Check price on Amazon

Pros

• Holds a gun, foam cannon, nozzle and wand extension at the same time, so the whole wash kit hangs in one place.
• Heavy metal build with a powder coated finish, listed for lasting durability.
• Comes as one whole body with no assembly, and predrilled mounting holes with hardware included.
• Comes with 1/4 inch quick connect male and female fittings for the gun and cannon.

Cons

• No warranty term is stated.
• No weight is stated, so the load on the wall fixings is not listed.
• Only black is listed.
• The listing does not state how many nozzle tips the rack holds.

2

4 Sets Foam Cannon Holder

succulentlovers·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A set of four stainless steel holders for foam cannons and nozzle tips, fitting standard 1/4 inch quick connects, with screw or adhesive mounting.

Check price on Amazon

Pros

• Four holders in the pack give a spot for a power washer and three foam cannons.
• Stainless steel build is corrosion-resistant and not easy to rust.
• Mounts with the included hardware or sticks to a smooth surface with double-sided tape.
• Adhesive pads, wall anchors and screws come in the pack.

Cons

• No warranty term is stated.
• No dimensions are stated, so the wall space each holder needs is not listed.
• The title says 4 Sets while the bullets describe 3 foam cannon holders and 1 foam holder, so the pack wording is mixed.
• The listing states a weight of 0.9 lb without saying if that is one holder or the whole set.

3

MYHLPER Pressure Washer Gun Holder,Foam Cannon

MYHLPER·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A metal wall rack with a powder coated finish that holds a pressure washer gun, foam cannon, 7 nozzle tips and 4 wand extensions, with 1/4 inch quick connect couplers.

Check price on Amazon

Pros

• Holds 7 nozzle tips and 4 wand extensions, plus a gun and a foam cannon, on one rack.
• Metal build with a powder coated finish, listed for lasting durability.
• Includes 4 screws for wall mounting.
• Comes with 1 pair of 1/4 inch quick connect male and female couplers.

Cons

• No warranty term is stated.
• No weight is stated.
• The part number and model name do not match: one says Gun Holder, the other says Foam Cannon Holder.
• The listing does not state the length of wand extension the holder takes.

4

RecDec 2 Pack Pressure Washer Nozzle Holder Holds

RecDec·9.6/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A pair of black plastic holders with 7 holes and 5 holes for spare 1/4 inch quick connect spray tips, with a hanging clip for the wash area.

Check price on Amazon

Pros

• Two holders in the pack: one with 7 holes and one with 5 holes for spare tips.
• Plastic build is listed as durable.
• Hanging clip keeps the holders by the wash area for quick tip changes.
• Made for 1/4 inch quick connect spare nozzles.

Cons

• No warranty term is stated.
• Nozzles are not included.
• The title says 2 Pack while the spec table lists NumberOfItems as 1.
• Plastic build, while the wall racks in this roundup use metal.

5

10 Pack Pressure Washer Nozzle Rubber Grommet

Verplexter·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A pack of 10 black rubber grommets that grip the base of a 1/4 inch quick connect nozzle and fit holes 3/4 in in diameter, for storing tips on the washer body.

Check price on Amazon

Pros

• Ten black rubber grommets in the pack.
• Soft, flexible interior grips the base of the nozzle and lets it pull out easily.
• Fits any 1/4 inch QC nozzle, with the grommet fitting holes 3/4 in in diameter.
• Replaces grommets on pressure washers with grooves for 1/8 in steel or thinner.

Cons

• No warranty term is stated.
• The title says 10 Pack while the part number reads 5-PK-Nozzle-Holders.
• The spec table lists two sizes: 0.875 by 0.875 by 0.25 in and 3 by 3 by 0.25 in.
• Grommets only, so the gun, foam cannon and wand still need a rack.

Compared on paper

Every rating comes from the brand’s listing and is not a shop test (gathered 12 November 2026). Where a listing contradicts itself, both figures are shown.

How the picks were scored

Each holder is scored out of 10 on performance, build, value, safety and warranty, with the weights published on the scoring method page. None states a UL, ETL or CSA listing, so all score zero on safety, and none states a warranty term, so all score zero on warranty.

No score drops under 9.2 or climbs past 9.8; a tool’s place inside those bounds is set by its weighted point total. A tool with no power source and no listed safety feature has safety removed, and the score is taken over 90 points.

What the listings tell you

Five listings were read. All five state a material and a 1/4 inch quick connect fit, four state dimensions, two state a weight, and none states a warranty term or a safety listing. Two listings contradict themselves on pack count, and one lists two different sizes.

How to pick the best pressure washer nozzle tip holder

Holder type

Wall racks hold the gun, cannon and tips in one place, while tip-only holders keep spare nozzles in a row. Grommets fit into a hole in the washer body and grip one tip each. Pick the type that matches the gear that ends up loose after a wash.

What it holds

Count the tips, the cannon and the wand before choosing. The MYHLPER rack holds 7 nozzle tips and 4 wand extensions, plus a gun and a foam cannon. The RecDec pair holds tips in a 7-hole holder and a 5-hole holder. The UNITEDPOWER rack holds a gun, foam cannon, nozzle and wand extension at the same time.

Mounting

Wall racks need screws and a solid spot on the wall. The UNITEDPOWER rack comes with predrilled mounting holes and hardware, and the MYHLPER rack includes 4 screws. The stainless steel set can be pinned to the wall with the included hardware or stuck to a smooth surface with double-sided tape, using the adhesive pads in the pack.

Material and finish

Stainless steel resists rust, heavy metal with a powder coated finish stands up to daily use, and plastic keeps the holder light. Rubber grommets grip the base of the nozzle and flex when a tip is pulled out.

Fit and quick connect size

Every pick here fits 1/4 inch quick connect nozzles. Check the fitting on the washer and the tips before ordering, and keep the soap tip and the rinse tips in separate slots so the right tip is at hand. A car wash soap for pressure washer works with the foam cannon that three of these holders store.

Garage Fit Check

• Measure the wall first: the UNITEDPOWER rack measures 11.22 by 1.97 by 4.71 in, and the RecDec holder measures 8.86 by 1.4 by 1.4 in.
• Check the fitting: every pick here fits 1/4 inch quick connect nozzles and tips.
• Count the tips on hand: the MYHLPER rack holds 7 nozzle tips, and the RecDec pair splits tips across 7-hole and 5-hole holders.
• Plan the mount: the stainless steel set includes adhesive pads, wall anchors and screws, while the metal racks include predrilled holes and screws.
• Leave room for the cannon: three of the picks hold a foam cannon as well as tips, so the cannon has a home between washes.

FAQ: garage tools

What pressure washer nozzle is used for a driveway?

A wide fan tip covers concrete faster, while a narrow tip cuts into packed grime. Keep both tips in the holder so swapping between them takes seconds and neither tip ends up on the floor.

What pressure washer nozzle is used for soap?

A soap tip runs at low pressure so the cannon can lay down foam. Keep the soap tip in its own slot, apart from the rinse tips, so it is easy to find when the cannon goes on.

What size O-ring fits a pressure washer nozzle?

O-ring size follows the fitting, not the holder. The holders in this roundup fit 1/4 inch quick connect nozzles, so match the O-ring to the 1/4 inch quick connect fitting on the washer and the tip.

How do you fix a pressure washer turbo nozzle?

A holder cannot fix a nozzle, but it can keep grit out of the fitting. Check the quick connect fitting for grit, rinse the tip, and fit a spare tip from the holder while the turbo nozzle is cleaned. Replace a tip that stays stuck or sprays unevenly.

What size is a pressure washer wand?

Wand length varies by model, so the fitting matters more than the length. The racks in this roundup hold wand extensions that fit 1/4 inch quick connect fittings, and the MYHLPER rack holds 4 wand extensions at once.

Related: the best electric pressure washer for cars, the best car wash soap for pressure washer, the complete detail brush set and the best pressure washer hose reel for mobile detailing. Also see the best electric pressure washer. Also see the best car wash pressure washer gun. Also see the pressure washer surface cleaner vs turbo nozzle. Also see the best pressure washer for car wash business.