Best Spring Compressor for Trucks (2026)

A truck strut job starts with a spring under serious load, and the only safe way to take that strut apart is to compress the coil first. A claw set that fits a car spring may not hold a truck spring, and a hydraulic unit that lives on the shop floor may not suit a driveway job. This guide compares coil spring compressors for truck work, so the best spring compressor for trucks can be picked from the listings, not from guesswork.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Picks for the garage

#	Product	Shop Score	Buy
1	OMT Hydraulic Strut Spring Compressor with 1 Ton	9.7/10	Buy on Amazon
2	CARVALAX 2670LB Heavy Duty Coil Spring Compressor	9.7/10	Buy on Amazon
3	Prokomon Heavy Duty Coil Spring Compressor Tool	9.5/10	Buy on Amazon
4	OMT Macpherson Strut Spring Compressor Tool Set	9.5/10	Buy on Amazon
5	WORKPRO 2-Piece Heavy Duty Coil Spring Compressor	9.5/10	Buy on Amazon

1

OMT Hydraulic Strut Spring Compressor with 1 Ton

Orion Motor Tech·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A hydraulic strut spring compressor with a 1 ton compression force and a 4.5 ton hydraulic jack capacity, built around an H-shaped base with a 12.6 in compression stroke and a safety chain.

Check price on Amazon

Pros

• A 1 ton compression force with a 4.5 ton hydraulic jack capacity suits heavy truck coil springs.
• A 12.6 in compression stroke with 8 height settings covers longer springs.
• Two large holders fit 5.5 to 6.7 in springs and two small holders fit 4.3 to 5.1 in springs.
• A locking mechanism holds the spring until the discharge pedal is pressed, and a 39.4 in safety chain adds a backup.

Cons

• The H-shaped base measures 41.3 by 18.0 by 41.3 in, so it needs real floor space.
• Floor anchoring uses two pre-drilled holes, so setup takes more work than a claw set.
• The listing states no socket or drive size, unlike the claw sets here.
• The listing gives no stated maximum spring wire diameter.

2

CARVALAX 2670LB Heavy Duty Coil Spring Compressor

CARVALAX·9.7/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A forged alloy steel claw set rated to 2,670 lb with a 1.8 to 11.4 in jaw opening, a dual safety mechanism and an extendable safety bracket for cars, trucks, ATVs and UTVs.

Check price on Amazon

Pros

• A 2,670 lb rating is the highest capacity among the claw sets here.
• The jaw opening of 1.8 to 11.4 in grips most standard automotive coil springs, with wire up to 0.8 in.
• A dual safety mechanism with a locking ring keeps clamping force on the coils.
• The safety bracket extends from 8.7 to 12.2 in to keep compression parallel.

Cons

• Two compressors must be tightened alternately, so the job takes longer than with the hydraulic pick.
• Only a 1 year manufacturer warranty is stated.
• The listing gives no overall dimensions for the set.
• No storage case is listed for the set.

3

Prokomon Heavy Duty Coil Spring Compressor Tool

Prokomon·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A heavy-duty claw set rated to 2,645 lb with reinforced locking hooks, a safety lock bracket and a carrying case for suspension work on cars, trucks, SUVs, ATVs and UTVs.

Check price on Amazon

Pros

• A 2,645 lb capacity covers heavy coil springs for trucks and SUVs.
• Reinforced locking hooks and a safety bracket hold springs in place during compression.
• Adjustable jaws grip different spring sizes for cars, trucks, SUVs, ATVs and UTVs.
• A complete set with a protective carrying case keeps the kit organized.

Cons

• The listing states no jaw opening, so spring fit cannot be checked before ordering.
• The listing states no maximum spring wire diameter.
• The listing states no socket or drive size.
• The spec table lists 52 items, which conflicts with the description of one complete set.

4

OMT Macpherson Strut Spring Compressor Tool Set

Orion Motor Tech·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A MacPherson strut spring compressor set with a 10.5 in range, Acme-threaded rods, detent pins and a 1/2 in square drive, in a blow-molded case.

Check price on Amazon

Pros

• The maker lists a 10.5 in range as wider than the competition, so it works with more vehicles.
• Acme-threaded rods with detent pins lock the rods in place for non-slip compression.
• Works with a manual or power tool through a 1/2 in square drive or 13/16 in hex sockets.
• Heat-treated steel with a black oxide finish on the rods and powder-coated heads resists corrosion.

Cons

• The listing states no load capacity, so the rating cannot be checked against truck springs.
• The listing states no jaw opening or maximum spring wire diameter.
• The listing states no safety bracket, unlike the other claw sets here.
• The listing describes the set as suited to small and medium-sized cars, so heavy truck springs may exceed its intended use.

5

WORKPRO 2-Piece Heavy Duty Coil Spring Compressor

WORKPRO·9.5/10 Shop Score

i

The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A two-piece claw set rated to 2,200 lb per pair with locking jaws, an adjustable safety bracket and a 19 mm socket drive, in a blue storage case.

Check price on Amazon

Pros

• A 2,200 lb rating per pair with jaws from 3.0 to 10.6 in covers a wide range of coil springs.
• Lock rings secure the hook jaws, and the curved sliding bracket adjusts from 8.6 to 12.2 in.
• Black-oxide 20# steel tubes, chrome-plated 45# steel hooks and a 40Cr screw rod heat-treated to HRC 38 to 45 resist wear and bending.
• The set includes two compressors, a safety bracket and a blue storage case, at approximately 4.6 kg total weight.

Cons

• No warranty term is stated.
• The set must be used with hand tools only; air and impact tools are not allowed.
• Two compressors must be tightened alternately to keep pressure even.
• The listing states no dimensions for the set.

Compared on paper

Every rating comes from the brand’s listing and is not a shop test (gathered 11 November 2026).

How the points were given

Each compressor is scored out of 10 on performance, build, value, safety and warranty. A stated locking mechanism, safety bracket or safety chain earns safety points, and a stated warranty term earns warranty points.

No score drops under 9.2 or climbs past 9.8; a tool’s place inside those bounds is set by its weighted point total.

What the listings tell you

Five coil spring compressor listings were compared. Four stated a warranty term and one did not. Four stated a load capacity and one did not. Two claw sets stated a jaw range and a maximum wire diameter, while the third claw set stated neither. Two listings carried a contradiction between the title or bullets and the spec table, and both are noted in the reviews below.

Buying guide: the best spring compressor for trucks

Capacity for truck springs

Truck coil springs carry more load than car springs, so check capacity first. The claw sets here are rated from 2,200 lb per pair to 2,670 lb, and the hydraulic pick lists a 1 ton compression force with a 4.5 ton jack capacity. One pick states no capacity at all.

Jaw opening and wire size

Fit is set by jaw opening and maximum wire diameter. The CARVALAX jaws open from 1.8 to 11.4 in and the WORKPRO jaws from 3.0 to 10.6 in, and both fit wire up to 0.8 in. The hydraulic pick uses holders instead: large holders for 5.5 to 6.7 in springs and small holders for 4.3 to 5.1 in springs. Measure the spring before ordering.

Hydraulic or claw style

A hydraulic unit compresses with a jack and a discharge pedal, which suits repeated strut work on heavy springs. A claw set needs two compressors tightened alternately, which takes longer but packs into a case. The hydraulic pick here lists 8 height settings and a 12.6 in stroke for longer springs.

Safety locks and brackets

Every pick here lists a locking feature: a locking mechanism and a 39.4 in safety chain on the hydraulic pick, locking rings and brackets on the claw sets, and detent pins on the OMT MacPherson set. Never get under a vehicle supported only by a jack; use rated jack stands on solid, level ground and follow the lift points in the owner’s manual.

Sockets and hand tools

Claw sets are driven by a socket or wrench: a 19 mm socket for the WORKPRO set and an included 3/4 in socket for the CARVALAX set, while the OMT MacPherson set takes a 1/2 in square drive or 13/16 in hex. Grease the threads before use, tighten both sides alternately, and use hand tools only.

Garage Fit Check

• The hydraulic pick measures 41.3 by 18.0 by 41.3 in and anchors to the floor through two pre-drilled holes, so allow a fixed spot for it.
• The claw sets pack into cases, including a blue storage case for the WORKPRO set and a blow-molded case for the OMT MacPherson set.
• Check the spring against the holder sizes or the jaw opening before the first job: 5.5 to 6.7 in and 4.3 to 5.1 in holders on the hydraulic pick, or a 1.8 to 11.4 in jaw opening on the CARVALAX set.
• Check the drive size on hand: a 19 mm socket, a 3/4 in socket, or a 1/2 in square drive with a 13/16 in hex.

FAQ: garage tools

What does a coil spring compressor do?

It compresses a coil spring so a strut can be taken apart and put back together for suspension work, covering removal and installation of coil springs, struts and shock absorbers. Without compression, the spring stays under load and cannot be removed safely.

How do you use coil spring clamps?

Install one compressor on each side of the spring and tighten alternately to keep pressure even, greasing the threads before use. Drive the hex bolt with a socket or wrench, such as a 19 mm socket or the included 3/4 in socket, and use hand tools only.

Can a coil spring compressor handle truck springs?

It depends on the rating. The claw sets here are rated from 2,200 lb per pair to 2,670 lb, and the hydraulic pick lists a 1 ton compression force with a 4.5 ton jack capacity. Check the rating and the spring size against the listing before ordering.

Hydraulic or manual: which coil spring compressor suits a truck strut job?

A hydraulic pick suits repeated work on heavy truck springs, with a 1 ton compression force, a 12.6 in stroke and 8 height settings. A claw set suits occasional jobs and stores in a case, with ratings from 2,200 lb per pair to 2,670 lb. Either way, match the rating and the spring size to the listing.

Related: the best coil spring compressor tool, the best coil spring compressor for beginners, the best coil spring compressor under 60, valve spring compressor vs coil spring compressor, how many jack stands do you need and the best all in one jack and jack stand.