Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

C Clamp Sizes: Throat Depth and Capacity Chart

C clamp sizes explained by jaw opening and throat depth, with a chart of the sizes in the sets below and how to measure for the right one.

C Clamp Sizes: Throat Depth and Capacity Chart
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Wilton Spark-Duty Hi-Vis C-Clamp SetWilton Spark-Duty Hi-Vis C-Clamp Set9.7/10View on Amazon
  2. 2WOPPLXY 4 Pcs 6 Inch Heavy Duty C ClampsWOPPLXY 4 Pcs 6 Inch Heavy Duty C Clamps9.4/10View on Amazon
  3. 3WILLBOND 4 Pcs C Clamps Set 3'' 4'' 6'' 8'' HeavyWILLBOND 4 Pcs C Clamps Set 3'' 4'' 6'' 8'' Heavy9.3/10View on Amazon

C clamp sizes are named by jaw opening, the widest gap the clamp can hold. Throat depth is a separate figure: how far the frame reaches in from the edge of the work. To pick one, match the opening to the thickness of the material you are clamping and the throat to how far in from the edge the clamp must reach. This guide explains c clamp sizes with a chart drawn from the sets below, so you can measure the job and pick the clamp that fits it.

GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.

Below: the measurements that name a C clamp, a chart of the sizes in the sets here, and how to measure for the right one.

Wilton Spark-Duty Hi-Vis C-Clamp Set

Wilton Spark-Duty Hi-Vis C-Clamp Set

Wilton9.7/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-piece drop-forged steel C-clamp set in 2, 4, 6 and 8 in sizes with copper-plated spindles, a V-grooved anvil and a lifetime warranty.

Pros

  • Four sizes in one kit: 2, 4, 6 and 8 in clamps
  • Drop-forged steel frames with an extra-deep throat
  • Copper-plated spindles and swivel pads resist weld spatter
  • Hi-vis yellow finish meets the OSHA 1910.144 safety color standard

Cons

  • No carrying case is included, only a retail box
  • Serrated pads sold separately
  • Heavier than most woodworking glue-ups need, at 16.0 lb for the kit
  • The largest clamp opens to 8-1/4 in, so thicker stock needs a bigger clamp
WOPPLXY 4 Pcs 6 Inch Heavy Duty C Clamps

WOPPLXY 4 Pcs 6 Inch Heavy Duty C Clamps

WOPPLXY9.4/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-piece set of 6 in heavy-duty cast iron C clamps with a 6 in jaw opening, a 3 in throat depth and a clamping force of up to 1,200 lb.

Pros

  • Jaw opening of 6 in with a 3 in throat depth, both stated
  • Clamping force of up to 1,200 lb
  • Heavy-duty cast iron with a green coating that resists rust
  • Sliding T-bar handle with a smooth threaded rod

Cons

  • Only the 6 in size is included, so it covers no other opening
  • A 3 in throat depth limits how far in from the edge it can reach
  • Clamping thickness reaches 6 in, so thicker stock needs a larger clamp
  • No warranty term is stated
WILLBOND 4 Pcs C Clamps Set 3'' 4'' 6'' 8'' Heavy

WILLBOND 4 Pcs C Clamps Set 3'' 4'' 6'' 8'' Heavy

WILLBOND9.3/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-piece steel C-clamp set in 3, 4, 6 and 8 in sizes with sliding T-bar handles for woodworking, metalwork, welding and automotive work.

Pros

  • Four sizes in one set: 3, 4, 6 and 8 in
  • Steel construction, sturdy and reusable
  • Sliding T-bar handle for torque with less hand fatigue
  • Adjustable positioning screws fit most tabletops and wood strips

Cons

  • No throat depth is stated for any size
  • No clamping force is stated
  • No warranty term is stated
  • The set starts at 3 in, so there is no 2 in clamp in the kit

C clamp sizes: opening and throat depth

A C clamp is named by its jaw opening. The opening is the gap between the anvil and the pad when the screw is wound out, and it sets the thickest stack the clamp can close on. Throat depth is the reach of the frame: the distance from the inside of the frame to the centre line of the screw, which sets how far in from the edge of the work the clamp can grip. A clamp with a deep throat reaches past a wide edge; a clamp with a shallow throat grips close to the edge only.

Clamping force is the third figure on a listing, rated in pounds, and it sets how hard the clamp can press the joint together. The Wilton set rates each size separately, from 3,500 lb on the smallest to 6,900 lb on the largest, while the WOPPLXY set is rated up to 1,200 lb. The WILLBOND listing states no clamping force, so its sizes are the only guide to what each clamp covers.

Clamp Jaw opening Throat depth Clamping force
Wilton 2 in 0-2-1/8 in 2-1/4 in 3,500 lb
Wilton 4 in 0-4-1/4 in 3-1/4 in 6,200 lb
Wilton 6 in 0-6-1/16 in 4-1/16 in 6,600 lb
Wilton 8 in 0-8-1/4 in 4-15/16 in 6,900 lb
WOPPLXY 6 in 6 in 3 in Up to 1,200 lb
WILLBOND 3 in Not stated Not stated Not stated
WILLBOND 4 in Not stated Not stated Not stated
WILLBOND 6 in Not stated Not stated Not stated
WILLBOND 8 in Not stated Not stated Not stated

Read the chart by size first, then check the throat. A clamp whose opening covers the stack but whose throat stops short of the joint will not hold the work where it counts.

How to measure for the right C clamp size

  1. Measure the thickness of the stack at the point you will clamp, with every layer in place. Pick an opening that covers that thickness.
  2. Measure from the edge of the work to the centre of the joint. Pick a throat depth that reaches that far, with room to spare.
  3. Check the rated force. The sets here run from a WOPPLXY rating of up to 1,200 lb to a Wilton rating of up to 6,900 lb, so match the rating to the job: light holding needs less than a joint that must stay pressed tight while glue sets.
  4. Check what else is in the box. The Wilton set arrives as four clamps in a retail box with no carrying case, so plan where the clamps will live on the bench or the wall.
Garage safety

Read the manual before first use, wear eye protection, keep the work area clear and ventilated, and stay within every stated rating. Read our Safety Disclaimer.

The clamps that cover these sizes

The sets below cover the sizes in the chart above, so the measuring step above ends with a clamp in hand: the Wilton set handles welding and fabrication across the full range, the WOPPLXY set covers the 6 in size for woodworking and general work, and the WILLBOND set covers general clamping across the range. Each set below lists the sizes it covers, with the opening and throat where the maker lists them, and the force where it is rated.

FAQ: garage tools

What does C clamp size mean?

The size is the nominal jaw opening, the widest gap the clamp can hold. A 6 in clamp is named for an opening of about 6 in: the Wilton 6 in clamp opens to 6-1/16 in, while the WOPPLXY 6 in clamp opens to 6 in. The throat depth says how far in from the edge it can reach.

What is throat depth on a C clamp?

Throat depth is how far the frame reaches in from the edge of the work. In the sets here it runs from 2-1/4 in on the smallest Wilton clamp to 4-15/16 in on the largest, with the WOPPLXY clamp (on Amazon) at 3 in.

How do I know which C clamp size I need?

Measure the thickness of the stack and the distance from the edge to the joint, then pick a clamp whose opening covers the thickness and whose throat reaches the joint. The chart above lists the opening and throat for each size in the sets here.

What clamping force do I need?

It depends on the job. The sets here are rated from up to 1,200 lb on the WOPPLXY clamps to up to 6,900 lb on the largest Wilton clamp, so a light hold needs less force than a joint that must stay pressed tight while glue sets.

Can I use a C clamp for welding?

Yes, and the Wilton set is made for it: copper-plated spindles and swivel pads resist weld spatter, and a V-grooved anvil holds rounds, squares and flats. The WILLBOND and WOPPLXY sets also list welding among their uses.

Do C clamps come in sets?

The sets here all arrive as 4-piece sets: the Wilton set in 2, 4, 6 and 8 in sizes, the WILLBOND set in 3, 4, 6 and 8 in sizes, and the WOPPLXY set as four 6 in clamps.

Related: bar clamp vs C clamp, our best C clamp sets and the garage upgrades hub.

More buying guides

Garage Upgrades ·

C Clamp Types and Uses

C clamp types by jaw opening, throat depth and handle: four sets from 3 to 8 inches compared, with clamping force, materials and pack…

Garage Upgrades ·

Best Clamp on Trouble Light (2026)

5 clamp-on trouble lights for the garage compared on brightness, power, mounting and warranty, with a verdict for home mechanics.