Floor Jack vs Jack Stands: Which One Should You Buy?
A floor jack lifts the car and jack stands hold it up: how each side works, the height and capacity the listings state, and which side fits brakes, oil changes and wheels-off jobs.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Big RED 3 Ton (6000 LBs) Jack Stands9.6/10View on Amazon - 2
VEVOR 3 Ton Low Profile Aluminum & Steel Racing9.6/10View on Amazon - 3
Jack Stands with Double Locking and Large Foot9.6/10View on Amazon - 4
3 Ton Low-Profile Hydraulic Floor Jack,Durable9.5/10View on Amazon
Verdict: Choose a floor jack if you need to lift the car for a tire change, an oil change or brake work, then lower it onto stands before going under. Choose jack stands if you need to hold the car up while you work under it, and pair them with a jack you already own.
Both belong in the same job, but they do different work. A floor jack raises the car, and jack stands hold it up once it is raised. This floor jack vs jack stands comparison covers both sides, then examples of each from the listings reviewed.
GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.
Example jacks and stands

Big RED 3 Ton (6000 LBs) Jack Stands
A 2 pack of 3 ton jack stands, adjustable from 11.25 inches to 16.75 inches, with a multi-position ratchet bar and a wide pyramid foot base.
Pros
- Adjustable height range of 11.25 inches to 16.75 inches with a multi-position ratchet bar
- Sawtooth design with pawl and tooth for extra protection
- Wide pyramid-shaped foot base and large saddle surface for stable support
- 1 year manufacturer warranty stated in the listing
Cons
- Not recommended for large trucks
- 6,000 lb stated capacity, below the PRUTHY pair's 6,600 lb
- No safety pins stated, unlike the double locking PRUTHY stands
- No handle stated for carrying or adjustment

VEVOR 3 Ton Low Profile Aluminum & Steel Racing
A 3 ton low profile aluminum and steel racing floor jack with dual pistons, a lifting range of 3-6/11 inches to 19-11/16 inches, and 4 wheels for rolling under the car.
Pros
- Dual pistons lift to full height in 7 strokes
- Lifting range of 3-6/11 inches to 19-11/16 inches for low cars and SUVs
- Heavy-duty steel and durable aluminum construction with 4 wheels
- ASME PALD-2014, CE and UKCA stated, with a built-in load system
Cons
- No warranty term stated
- Minimum height of 3-6/11 inches, above the LARBANKE jack's 3.15 inches
- No saddle diameter stated
- Two-piece handle needs assembly before use

Jack Stands with Double Locking and Large Foot
A pair of 3 ton jack stands with double locking, a lifting range of 11.4 inches to 16.9 inches and a large foot base, for SUVs, trailers and cars.
Pros
- Double locking: locking ratchet bar and metal safety pins
- Lifting range of 11.4 to 16.9 inches (29 to 43 cm)
- Ratchet bar forged from ductile iron in one piece
- Wide pyramid foot base and large top saddle for stable support
Cons
- No ASME or ALI standard named, only national safety standards
- Handle doubles as the saddle release, so it must stay with the stands
- No weight stated for the pair
- No saddle size stated

3 Ton Low-Profile Hydraulic Floor Jack,Durable
A 3 ton low profile hydraulic floor jack with a dual piston pump, a lifting range of 3.15 inches to 18.31 inches, and a 4-wheel system for rolling under the car.
Pros
- Dual piston hydraulic pump for a fast and smooth lift
- Lifting range of 3.15 inches to 18.31 inches for sedans, trucks and SUVs
- Heavy-duty steel and high-strength carbon construction
- 4 wheels: 2 large steel front casters and 2 360-degree swivel casters
Cons
- No warranty term stated
- No certification stated
- No weight stated
- Maximum height of 18.31 inches, below the VEVOR jack's 19-11/16 inches
Other tools worth a look
VEVOR 3 Ton Low Profile Floor Jack for All Terrain VehiclesCheck price on Amazon
Bonnlo 3 Ton Low Profile Floor JackCheck price on Amazon
Jack Stands 3 TonCheck price on Amazon
GEARWRENCH 3.5 Ton Low Profile Floor JackCheck price on Amazon
LARBANKE 2.5T Floor JackCheck price on Amazon
5 Ton Hydraulic Low Profile Floor JackCheck price on Amazon
Side by side: floor jack vs jack stands
| Floor jack | Jack stands | Note | |
|---|---|---|---|
| What it does | Lifts the car off the ground | Holds the car up after the jack lifts it | Different jobs |
| How it holds the car | Hydraulic pump raises the saddle; the car rests on the jack only while lifting | Ratchet bar locks the saddle at height; the car rests on the stands | Stands lock |
| Height range (examples) | 3-6/11 in to 19-11/16 in (VEVOR); 3.15 in to 18.31 in (LARBANKE) | 11.25 in to 16.75 in (Big RED); 11.4 in to 16.9 in (PRUTHY) | Jacks lift higher |
| Capacity (examples) | 3 tons, 6,600 lb (both jacks) | 3 ton, 6,000 lb (Big RED); 3 ton, 6,600 lb (PRUTHY) | All 3 tons |
| Safety hardware (examples) | Built-in load system; ASME PALD-2014 (VEVOR) | Ratchet bar with pawl and tooth (Big RED); double locking pins (PRUTHY) | VEVOR and Big RED only |
| Warranty (examples) | Not stated (both jacks) | 1 year manufacturer warranty (Big RED); limited 1-year warranty (PRUTHY) | Stands only |
| Moving it | 4 wheels; rolls under the car | No wheels; set by hand under the lift points | Jacks roll |
| Working under the car | Never get under a vehicle on a jack alone | Rated stands on solid level ground | Safety first |
We copy each listing’s rated specs exactly as the manufacturer gives them; as of 20 October 2026.
How each one holds the car
A floor jack lifts the car with a hydraulic pump and a saddle: the VEVOR jack uses dual pistons and a dual parallel pump system, and the LARBANKE jack a dual piston hydraulic pump. The car rests on the jack only while lifting. Jack stands hold the car after the lift: a ratchet bar locks the saddle at height, the Big RED pair adds a pawl and tooth, and the PRUTHY pair adds metal safety pins as a double lock. The car rests on the stands during the work.
Height range
The floor jacks start lower and lift higher. The VEVOR jack ranges from 3-6/11 inches to 19-11/16 inches, and the LARBANKE jack from 3.15 inches to 18.31 inches. The stands cover the middle of that range: the Big RED pair adjusts from 11.25 inches to 16.75 inches, and the PRUTHY pair from 11.4 inches to 16.9 inches. Lift past the height you need, set the stands, then lower the car onto them.
Capacity
All four examples are rated at 3 tons: the two floor jacks state 3 tons and 6,600 lb, the PRUTHY stands 3 ton and 6,600 lb, and the Big RED stands 3 ton and 6,000 lb. The Big RED listing calls its stands suitable for most 3 ton autos, and notes they are not recommended for large trucks. Match the capacity to the vehicle, and check the owner’s manual lift points before lifting.
Safety: jacks lift, stands hold
Never get under a vehicle on a jack alone. A jack lifts; stands hold. Set rated stands on solid level ground, at the lift points in the owner’s manual, and lower the car onto them before going under. The VEVOR jack adds a built-in load system that avoids use beyond load capacity, and states CE, UKCA and ASME PALD-2014 compliance. The Big RED stands state they meet ASME standards, and the PRUTHY stands state double locking pins and national safety standards. The LARBANKE jack states no certification.
Choose a floor jack if
- You need to lift the car for a tire change, an oil change or brake work
- You want a low profile jack that rolls under a low car
- You already own rated stands to hold the car after the lift
- You want dual pistons and a wide lifting range
Choose jack stands if
- You need to hold the car up while you work under it
- You already own a jack to lift the car first
- You want a locking ratchet bar at height
- You want a pair with a 1 year manufacturer warranty
For more choices, see the best jack stands and the best emergency scissor jack.
A jack is for lifting, not holding. Never work under a vehicle supported only by a jack: set it on rated jack stands, on solid, level ground, at the manufacturer's lift points, chock the wheels, and give the car a firm shake before you go under. Read our Safety Disclaimer.
Garage Fit Check
- Space: the VEVOR jack measures 29 inches by 12.8 inches by 5.9 inches and the LARBANKE jack 24.21 inches by 13.19 inches by 3.15 inches.
- Power: no outlet needed; both jacks are hydraulic and the stands lock by hand.
- Moving: both jacks roll on 4 wheels, and both handles detach for storage.
- Storage: the Big RED pair measures 11.22 inches by 7.5 inches by 6.7 inches and weighs 13.9 pounds.
- What to check: the stands start at 11.25 inches and 11.4 inches, so lift past those heights before setting the stands.
FAQ: garage tools
Can I work under a car on a floor jack?
No. Never get under a vehicle on a jack alone. Lift with the jack, set rated stands on solid level ground at the manual’s lift points, and lower the car onto the stands before going under.
Do I need both a floor jack and jack stands?
Yes, for any job under the car: the jack lifts and the stands hold, and neither side does both jobs.
What height jack stands do I need?
Stands that reach the height the job needs and fit under the car once the jack lifts it: the Big RED pair adjusts from 11.25 inches to 16.75 inches and the PRUTHY pair from 11.4 inches to 16.9 inches.
Are 3 ton jacks and stands enough for a car?
All four examples here are rated at 3 tons. The Big RED listing calls its stands suitable for most 3 ton autos, and notes they are not recommended for large trucks. Match the capacity to the vehicle.
Which side should I buy first?
A floor jack first if you have no way to lift the car, and stands first if you already own a jack. Under the car, both are needed: the jack lifts and the stands hold.
Related: the best jack stands, the jacks and stands hub, how to use a jack lift safely and electric vs hydraulic floor jack.




