Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Pressure Washer Pump Types Explained

Pressure washer pump types split into axial cam and triplex plunger designs, and the right pump depends on shaft size, engine power and how often the washer runs.

Pressure Washer Pump Types Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YAMATIC 7/8" Vertical Shaft Pressure Washer PumpYAMATIC 7/8" Vertical Shaft Pressure Washer Pump9.6/10View on Amazon
  2. 2Horizontal Pressure Washer PumpHorizontal Pressure Washer Pump9.5/10View on Amazon
  3. 3TOOLCY Pressure Washer Pump 1" Shaft 3600-4400 PSITOOLCY Pressure Washer Pump 1" Shaft 3600-4400 PSI9.5/10View on Amazon
  4. 4VEVOR Pressure Washer Pump 4400 PSI 4.0 GPM 1"VEVOR Pressure Washer Pump 4400 PSI 4.0 GPM 1"9.5/10View on Amazon

A pressure washer that has lost its bite usually points at the pump. The engine still runs, the hose still holds water, but the spray comes out weak and the driveway stays dirty. Pressure washer pump types come down to axial cam and triplex plunger designs, and the right pump depends on shaft size, engine power and how often the washer runs. Match those, and a fresh pump brings the old washer back to work.

GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.

Below: the two pump designs, how to match a pump to an engine, what PSI and GPM mean together, and the safety checks to run before the first job.

YAMATIC 7/8" Vertical Shaft Pressure Washer Pump

YAMATIC 7/8" Vertical Shaft Pressure Washer Pump

YAMATIC9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 7/8 inch vertical shaft axial cam pump rated at 3000 PSI and 2.5 GPM for 160-201cc engines.

Pros

  • 3000 PSI and 2.5 GPM for household-grade washers
  • Thermal relief valve guards against overheating in bypass mode
  • Adjustable unloader sets pressure to suit the engine
  • Pre-filled oil and a 10-minute setup, per the maker

Cons

  • Not for 3/4 inch shafts, horizontal engines or front inlet and outlet
  • No warranty term is stated
  • 200 hours of running life is the lowest span in this guide
  • Suits 5.0-6.0 HP engines only, so larger washers need a bigger pump
Horizontal Pressure Washer Pump

Horizontal Pressure Washer Pump

SMMMT9.5/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/4 inch horizontal shaft triplex plunger pump rated at 2600-3300 PSI and 2.4 GPM for 5.5-7HP engines.

Pros

  • 2600-3300 PSI and 2.4 GPM from a triplex plunger pump
  • Forged brass body resists corrosion
  • Thermal relief valve guards against overheating in bypass mode
  • Working time of up to 500 hrs

Cons

  • No warranty term is stated
  • 2.4 GPM is the lowest flow in this guide
  • 11.0 lb is heavier than the axial cam pump in this guide
  • Fits 5.5-7HP engines only, so larger washers need a bigger pump
TOOLCY Pressure Washer Pump 1" Shaft 3600-4400 PSI

TOOLCY Pressure Washer Pump 1" Shaft 3600-4400 PSI

TOOLCY9.5/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 inch horizontal shaft triplex pump rated at 3600-4400 PSI and 4 GPM with chemical injection for 9-15HP engines.

Pros

  • 3600-4400 PSI and 4 GPM for driveways, decks and fences
  • Triplex design with a solid brass pump head
  • Adjustable unloader and chemical injection
  • Sight glass shows the oil level without a dipstick

Cons

  • Cold water only; never feed it hot water
  • Fits 9-15HP engines only, so smaller washers cannot use it
  • Oil change needed every 60 hours of running time
  • 14.0 x 13.7 x 7.3 in body is the largest in this guide
VEVOR Pressure Washer Pump 4400 PSI 4.0 GPM 1"

VEVOR Pressure Washer Pump 4400 PSI 4.0 GPM 1"

VEVOR9.5/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 inch horizontal shaft triplex plunger pump rated at 4400 PSI and 4.0 GPM with a forged brass head.

Pros

  • 4400 PSI and 4.0 GPM for walls, sidewalks, cars and job sites
  • One-piece forged brass pump head for sealing and strength
  • Sight glass shows the oil level without a dipstick
  • Standard SAE bolt pattern fits many horizontal engines

Cons

  • Fits horizontal engines with a 1 inch shaft only
  • Pressure ships below its maximum and needs adjusting before the first job
  • 12.4 x 10.23 x 7.28 in body needs mounting room on the washer
  • No stated running life in hours

Pressure washer pump types: axial cam vs triplex plunger

Type How it is built What the listings show
Axial cam A cam drives the pistons in a compact body 3000 PSI and 2.5 GPM on the YAMATIC, rated for 200 hours, built for household-grade washers
Triplex plunger Plungers share the work across a brass head 4400 PSI and 4.0 GPM on the VEVOR and TOOLCY, 2600-3300 PSI and 2.4 GPM on the SMMMT

The axial cam pump in this guide is the lighter, simpler option: the YAMATIC weighs 6.4 lb and fits household-grade washers with 160-201cc engines. The triplex pumps weigh more, but their brass heads suit washers that run often: the SMMMT lists a working time of up to 500 hrs, and the SMMMT and TOOLCY list driveways, decks and fences among their uses. The axial vs triplex pump pressure washer comparison goes deeper into the two designs.

Match the shaft and the engine first

A pump only fits if the shaft matches. The YAMATIC takes a 7/8 inch vertical shaft with a rear inlet and outlet, the SMMMT takes a 3/4 inch horizontal shaft, and the VEVOR and TOOLCY take a 1 inch horizontal shaft. Measure the shaft and check the inlet and outlet orientation before ordering: the YAMATIC listing states it is not for 3/4 inch shafts, horizontal engines, front inlet and outlet, or idle-down systems.

Then match the engine. The YAMATIC suits 160-201cc engines in the 5.0-6.0 HP range, the SMMMT suits 5.5-7HP engines, and the TOOLCY fits engines of 9-15HP or 270-420cc. All four pumps use an SAE standard bolt pattern or flange, but that alone does not guarantee the holes line up, so check the flange dimensions against the old pump before ordering.

PSI and GPM: read them together

PSI is the pressure at the nozzle and GPM is the flow that carries dirt away. The pumps in this guide span 2600 PSI to 4400 PSI and 2.4 GPM to 4.0 GPM: the YAMATIC is rated at 3000 PSI and 2.5 GPM, the SMMMT at 2600-3300 PSI and 2.4 GPM, and the VEVOR and TOOLCY at 4400 PSI and 4.0 GPM. The TOOLCY listing recommends a working pressure of 3400 PSI at 3400 RPM for longer life, and both the VEVOR and SMMMT listings note the pressure ships below its maximum, so the adjustable unloader or regulator sets the working pressure for each job.

Read the manual for the washer before swapping a pump, and check the rated speed: the YAMATIC lists a rated speed of 3400 RPM, and the TOOLCY lists the same 3400 RPM with its recommended working pressure. The how to choose a pressure washer guide covers matching a washer to the job, and the types of pressure washers guide shows the wider range of washers.

Pressure washer safety

A pressure washer can cut skin and damage paint, siding and wood, so treat the spray like a tool, not a hose. Wear eye protection, keep the spray away from people and pets, and start with the nozzle farther from the surface.

The TOOLCY pump (on Amazon) is for cold water only, so never feed it hot water. The YAMATIC and the SMMMT each list a thermal relief valve that guards the pump when the trigger is released and the pump keeps running in bypass mode. The YAMATIC valve releases small amounts of hot water and draws in cooler water, and the SMMMT valve safeguards the pump against excessive heating during bypass operation. Check the manual for the washer before the first job, and never run a gas engine in a closed garage.

Garage safety

Read the manual before first use, wear eye protection, keep the work area clear and ventilated, and stay within every stated rating. Read our Safety Disclaimer.

Gear that shows the pressure washer pump types

The pump is the part that sets PSI and GPM, so the 4 pumps below show each design, shaft size and engine range in the guide above.

FAQ: garage tools

What is the difference between an axial cam and a triplex pump?

An axial cam pump drives its pistons from a cam in a compact body: the YAMATIC in this guide runs at 3000 PSI and 2.5 GPM with a rated running life of 200 hours. A triplex plunger pump spreads the work across a brass head, and the triplex pumps in this guide run 2600 PSI to 4400 PSI and 2.4 GPM to 4.0 GPM, with the SMMMT rated up to 500 hrs. A triplex pump suits a washer that runs often when the maker states a long working time, as the SMMMT does at up to 500 hrs; an axial cam pump suits a household-grade washer, as the YAMATIC is rated for household-grade use.

How do I know which pump fits my pressure washer?

Match the shaft size and orientation, the engine, and the PSI and GPM. The YAMATIC takes a 7/8 inch vertical shaft, the SMMMT takes a 3/4 inch horizontal shaft, and the VEVOR and TOOLCY take a 1 inch horizontal shaft. Then check the engine range each listing states, from 160-201cc on the YAMATIC to 9-15HP or 270-420cc on the TOOLCY.

Can I put a 4400 PSI pump on a small engine?

Only if the engine matches the pump’s listing. The VEVOR and TOOLCY pumps are rated at 4400 PSI and 4.0 GPM, and the TOOLCY fits engines of 9-15HP or 270-420cc. A pump needs the engine power its listing states to reach its rated PSI, so check the engine range before ordering a higher-rated pump for a small washer.

How long does a pressure washer pump last?

It depends on the pump and how often it runs. The YAMATIC is rated for 200 hours of running life, and the SMMMT lists a working time of up to 500 hrs. A thermal relief valve helps in bypass mode, and the TOOLCY listing recommends an oil change every 60 hours of running time.

Do I need to change the pump oil?

The TOOLCY listing recommends an oil change every 60 hours of running time. The YAMATIC ships with pre-filled oil, and the VEVOR and TOOLCY listings show a sight glass for checking the oil level without a dipstick. See the what type of oil for a pressure washer pump guide for the oil itself.

What is a thermal relief valve?

A thermal relief valve guards the pump against overheating in bypass mode, when the trigger is released and the pump keeps running. The YAMATIC listing states its valve releases small amounts of hot water and draws in cooler water, and the SMMMT listing states the same protection during bypass operation.

Related: the engine and shop equipment hub, axial vs triplex pump pressure washer and best gas pressure washer. Also see the best electric pressure washer guide and pressure washer pump repair.

More buying guides