Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Remove a Pressure Washer Pump: A Step-by-Step Guide

How to remove a pressure washer pump, from releasing the pressure to sliding the pump off the shaft, and which seal or rebuild kit fits your pump.

How to Remove a Pressure Washer Pump: A Step-by-Step Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 134262 Seal Kit for CAT Pump 66DX 6DX Pumps34262 Seal Kit for CAT Pump 66DX 6DX Pumps9.7/10View on Amazon
  2. 2Rebuild 20mm Pressure Washer Pump Rebuild KitRebuild 20mm Pressure Washer Pump Rebuild Kit9.6/10View on Amazon
  3. 36-Pack AR2235 Pressure Washer Water Seal Kit6-Pack AR2235 Pressure Washer Water Seal Kit9.6/10View on Amazon
  4. 4Madelyn 7104223 Compatible for Simpson CleaningMadelyn 7104223 Compatible for Simpson Cleaning9.4/10View on Amazon

A pressure washer that leaks at the pump or has lost its punch often needs its seals changed, and that job starts with getting the pump off the machine. How to remove a pressure washer pump comes down to a short run of steps: cut the power, release the pressure, disconnect the hoses, unbolt the pump and slide it off the drive shaft. With the pump on the bench, the seals and valves are in reach, and the right kit can be matched to the pump model before anything goes back together.

GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.

34262 Seal Kit for CAT Pump 66DX 6DX Pumps

34262 Seal Kit for CAT Pump 66DX 6DX Pumps

Yoursme9.7/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 15-piece NBR seal kit for CAT Pump 66DX and 6DX pressure washer pumps, rated to handle temperatures up to 160°F, with a 12 months' warranty.

Pros

  • Fits CAT Pump 66DX and 6DX models
  • NBR rubber resists oxidation, wear, tear, UV rays and solvents
  • Handles temperatures up to 160°F
  • 15 pieces cover washers, LPS seals, O-rings, V-packing and adapters

Cons

  • Fits only the listed CAT 66DX and 6DX models
  • Seals only; no valve plates or seats in the kit
  • Rubber seals are wear parts and need replacing after long service
  • Small parts are easy to mix up during a rebuild
Rebuild 20mm Pressure Washer Pump Rebuild Kit

Rebuild 20mm Pressure Washer Pump Rebuild Kit

Otoolling9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13-part rebuild kit for General Pump models with 20mm pistons, with steel valve parts and plastic mating parts, sized 4.13 by 3.86 by 2.17 inches.

Pros

  • 13 parts cover valve plates, springs, seals, O-rings and gaskets
  • Fits General Pump models with 20mm pistons
  • Metal parts are machined from high-strength, corrosion-resistant steel
  • Complete set, so the rebuild needs no separate orders

Cons

  • Fits only General Pump models with 20mm pistons
  • No warranty term is stated
  • 13 small parts to keep in order during the rebuild
  • Mating parts are molded plastic, not metal throughout
6-Pack AR2235 Pressure Washer Water Seal Kit

6-Pack AR2235 Pressure Washer Water Seal Kit

PuBaDuoParts9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6-pack of AR2235 water seals for Briggs and Stratton and Annovi Reverberi RMW and RMV pressure washer pumps, sized 0.78 inches outside, 0.46 inches inside and 0.14 inches thick.

Pros

  • 6 seals in the pack cover multiple repairs
  • Exact seal measurements stated: 0.78 in outside, 0.46 in inside, 0.14 in thick
  • Replaces part numbers 204084GS, 200345GS, AR2235, AR42122, 42122 and 70-464
  • Fits Briggs and Stratton, Annovi Reverberi RMW and RMV pumps

Cons

  • Seals only; valve and spring parts are not in the pack
  • Fits only the listed RMW and RMV and Briggs and Stratton pumps
  • No warranty term is stated
  • One seal size only, so a wrong measurement means a wrong fit
Madelyn 7104223 Compatible for Simpson Cleaning

Madelyn 7104223 Compatible for Simpson Cleaning

MadelYN9.4/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A valve kit with 6 complete valves, O-rings and seats for Simpson Cleaning pressure washer pumps, part 7104223.

Pros

  • 6 complete valves with O-rings and seats
  • Fits the listed Simpson pump models
  • Valve kit covers the valve side of a pump rebuild
  • Direct replacement for part 7104223

Cons

  • Fits only the listed Simpson pumps
  • Valves only; seals and gaskets are not in the kit
  • Will not fix a pump that also leaks at the seals
  • Six small valve assemblies to fit one at a time

How to remove a pressure washer pump

Work on flat ground with room to set the pump down. Wear eye protection before touching any fitting, and never point the spray gun at people while releasing pressure.

  1. Switch the washer off and disconnect it from power: unplug an electric washer, or shut off a gas engine.
  2. Turn off the water supply and disconnect the garden hose from the pump inlet.
  3. Release the pressure. Squeeze the spray gun trigger until water stops coming out, then set the gun down.
  4. Disconnect the high-pressure hose from the pump outlet and drain any water left in the pump.
  5. Remove the bolts that hold the pump to the engine or motor, and keep them together in a tray.
  6. Slide the pump straight off the drive shaft, and note how the shaft lines up for refitting.
  7. Set the pump on the bench with the head facing up so seals, valves and small parts stay in place while you inspect them.

If the pump will not slide off, look for a bolt you missed before pulling harder. Forcing it risks damage to the shaft or the pump housing.

Detailing safety

Keep electric pressure washers on a GFCI outlet, never point the wand at people or pets, wear eye protection with polishers and chemicals, and read the label before mixing any cleaning products. Read our Safety Disclaimer.

Seal and rebuild kits for the pump job

The pump comes off so its seals and valves can be reached, and these kits cover that work: a seal kit for CAT pumps, a rebuild kit for General Pump models, a water seal kit for Briggs and Stratton and Annovi Reverberi pumps, and a valve kit for Simpson pumps.

Match the kit to your pump before you order

Check the model plate on the pump before ordering. The Yoursme kit fits CAT 66DX and 6DX models, the Otoolling kit fits General Pump models with 20mm pistons, the PuBaDuoParts kit replaces OEM part numbers, and the Madelyn kit fits Simpson pumps.

When the old seal is out, measure it. The AR2235 water seal measures 0.78 inches outside, 0.46 inches inside and 0.14 inches thick, and a seal that does not match will not seat right. Check the piston size too: the Otoolling kit is built for 20mm pistons.

FAQ: garage tools

Can I remove a pressure washer pump without draining it first?

You can, but the water left inside will spill across the bench, so turn off the water, disconnect the hoses, release the pressure and drain the pump first. Draining also leaves the seals and valves clear to inspect.

How do I know which seal kit fits my pump?

Match the pump model on the model plate to the kit listing, and measure the old seal when it comes out. The AR2235 seal measures 0.78 inches outside, 0.46 inches inside and 0.14 inches thick.

Do I need a whole new pump, or just seals?

Seals and valves are common wear parts, and a seal kit or rebuild kit covers them. The Yoursme kit covers the seals in a CAT pump, the Otoolling kit rebuilds a General Pump head, and the Madelyn kit covers the valves in a Simpson pump.

Can I reuse the old seals after the pump comes off?

No. Old seals age, crack and lose their shape, and putting them back risks the same leak returning. Fit fresh seals from a kit that matches the pump.

What is the difference between a seal kit and a rebuild kit?

A seal kit covers seals, O-rings and packing: the Yoursme kit holds 15 pieces and the AR2235 kit holds 6 seals. A rebuild kit adds valve parts to the seals: the Otoolling kit holds 13 parts, including valve plates, valve springs, seals, O-rings and gaskets.

Related: pressure washer pump types, pressure washer pump repair, what type of oil for a pressure washer pump, the car detailing hub and pressure washer repair parts.

More buying guides

Engine and Shop Equipment ·

Pressure Washer Pump Types Explained

Pressure washer pump types split into axial cam and triplex plunger designs, and the right pump depends on shaft size, engine power and how…