Two Post Lift Parts: Pads and Trays
Two post lift parts are the pads and trays that sit between the lift arms and the frame, and matching them to your lift starts with measuring the plate and the shaft.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
10000LB 2 Post Car Lift9.7/10View on Amazon - 2
KATOOL 12000 lbs Extra Height 167inch 2 Post Lift Two Post9.6/10View on Amazon - 3
12000 Lbs 4.0HP Two Post Lift Single Lock Release Auto Lift9.6/10View on Amazon
A brake job starts with the car in the air, and the lift pads are the small parts between the lift arms and the frame: two post lift parts are the pads and trays that sit between the lift arms and the frame. This guide explains what each part does and how to match it to your lift.
GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.
VOSAREA 4pcs Car Lifting Pads Auto Jacking Lift
A 4 pack of round rubber lift pads rated 2500 to 3500 lbs per pad that cushions the frame rail and guards against scratches.
Pros
- Rated 2500 to 3500 lbs per pad for cars, trucks and SUVs
- Recessed pad area seats the vehicle evenly before lifting
- Soft rubber cushions the frame rail and guards against scratches
- 4 pack covers a full set of lift arms
Cons
- Spec table lists a 12 x 12 cm size against the 11.4 cm, 4.5 inch diameter in the bullets
- Soft rubber needs broad, flush contact, so narrow ridges near the rim risk splitting
- No warranty term is stated
- Rubber pads only, no steel tray or height adjustment is included
4 Pack 35mm Shaft Diameter Car Lift Round Tray
A 4 pack of steel trays with rubber pads that screws up from 3.3 to 9 cm to set the lift height on a 2-post lift.
Pros
- Chrome vanadium steel tray with a rubber pad for strength
- Height adjusts from 3.3 to 9 cm for different vehicles
- Threaded design steadies the lift and cuts vibration and friction
- Widened tray area guards the chassis from metal contact
Cons
- Fits 35 mm shafts only, not 38 mm or 50 mm shafts
- No warranty term is stated
- No capacity figure is stated for the tray
- Steel tray needs a fit check before ordering
Yudylg 4-Pack Lift Square Rubber Arm Pads
A 4 pack of square rubber arm pads at 4-3/4 by 4-3/4 by 0.59 inches with listed fitment for Globe, BendPak and Danmar models.
Pros
- Square 4-3/4 by 4-3/4 inch pads with a 0.59 inch thickness
- Anti-slip surface texture helps keep vehicles steady
- Listed fitments cover Globe, BendPak and Danmar models
- 4 pack covers routine replacement on a 2-post lift
Cons
- Warranty description states no warranty
- Square pads only, no round option in this listing
- No capacity figure is stated
- Pad adds a fixed 0.59 inch with no height adjustment
Sporthfish Round Rubber Arm Pads for BendPak
A set of 4 round rubber arm pads about 5 inches across that slip on or over BendPak and Danmar lift arms.
Pros
- Round 5 inch pads slip on or over the lift arms
- Hard rubber with a circular pattern to reduce slipping
- Fits BendPak and Danmar lifts, and may fit rolling and bridge jack pads on many 4-post lifts
- Set of 4 covers a full lift
Cons
- No warranty term is stated
- No capacity figure is stated
- Diameter is given as approximately 5 inches, not exact
- Round pads only, no square option in this listing
Two post lift parts: what they are
Two post lift parts are the wear parts and contact parts of a two-post lift: the rubber pads that meet the frame and the trays and feet that set the height. The listings here cover pads and trays only.
| Pad | Type | Size | Pack |
|---|---|---|---|
| VOSAREA Lift Pads | Round rubber pad | 4.5 in diameter | 4 |
| Sporthfish Arm Pads | Round rubber arm pad | 5 in diameter | 4 |
| OWNWEEDA Tray Pads | Steel tray with rubber pad | 35 mm shaft | 4 |
| Yudylg Square Arm Pads | Square rubber arm pad | 4-3/4 x 4-3/4 x 0.59 in | 4 |
How to match pads to your lift
Measure the backing plate and the shaft
The VOSAREA listing lists an 11.4 cm, 4.5 inch diameter with 7 cm, 2.75 inch spacing, and says to verify both before ordering. The OWNWEEDA listing fits 35 mm shafts only and does not fit 38 mm or 50 mm shafts, so measure the shaft before ordering.
Match the pad to the lift model
The Sporthfish pads are round and slip on or over the arms, while the Yudylg pads are square. Check the fitment the listing names for your lift model instead of matching the pad shape to the arm.
Check the height the pad adds
The OWNWEEDA tray adjusts from 3.3 to 9 cm, so it can raise the contact point. The Yudylg pad is 0.59 inch thick, so it adds a fixed height. Check how much height each part adds before you lift.
Two post lift parts for the job
Matching the pad to the lift arms and the frame is the step that needs the right part, and the pads and trays below cover that step.
How to choose the best two post lift parts
Pick the pad shape and size
Start with the shape and the size. Round pads in this guide run 4.5 inches and 5 inches across, and the square pads run 4-3/4 inches across, so measure the backing plate and the shaft and pick the pad the listing names for your lift. See the best 2 post car lift pinch weld pads for pads made for pinch welds.
Pick steel or rubber
Rubber pads cushion the frame and guard against scratches. The OWNWEEDA listing pairs a chrome vanadium steel tray with a rubber pad, and the tray adjusts from 3.3 to 9 cm. For lift choices, see the best two post truck lift guide.
Check the fit before you order
Fit is the whole job with lift parts. Measure the backing plate and the shaft, and match the pad to the lift brand where the listing names one.
Lift safety comes first. Never get under a vehicle supported only by a jack. Use rated stands on solid, level ground, lift at the lift points in the owner’s manual, and follow the lift maker’s concrete and ceiling requirements.
Check the lift's rated capacity against your heaviest vehicle, and its ceiling and concrete requirements (thickness and strength) before you buy. Install it exactly as the manufacturer specifies, use the mechanical locks before you go under, and look for ALI certification on the model. See the Automotive Lift Institute (ALI). Read our Safety Disclaimer.
FAQ: garage tools
What are two post lift parts?
They are the pads, trays and feet that sit between the lift arms and the frame of a two-post lift. The listings here cover rubber pads and steel trays.
How do I know which lift pad fits my lift?
Measure the backing plate diameter and bolt hole spacing, and measure the shaft diameter. The VOSAREA listing gives an 11.4 cm, 4.5 inch diameter with 7 cm, 2.75 inch spacing, and the OWNWEEDA listing fits 35 mm shafts only.
Are round or square lift pads better?
Neither shape is better on its own. Match the pad to the lift model and the fitment the listing names: the Sporthfish pads are round and slip on or over the arms, and the Yudylg pads are square replacements for the listed Globe, BendPak and Danmar models.
Do lift pads wear out?
Yes. Watch for splitting or surface damage. The VOSAREA listing warns that narrow ridges near the rim can split the rubber, so replace a pad that shows damage.
Can I use a two post lift pad on a 4-post lift?
The Sporthfish listing says its pads may fit the rolling and bridge jack pads on many 4-post lifts. Check the fit against your lift before ordering.
Related: scissor lift vs two post lift, the best hydraulic car lift, our car lifts hub.
