Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Sandpaper to Remove Paint (2026)

Five sandpaper sheets and rolls for stripping paint, compared by grit range, sheet size, backing and wet or dry use.

Best Sandpaper to Remove Paint (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Virginia Abrasives 80Best OverallVirginia Abrasives 809.6/10View on Amazon
  2. 2BMOTL Wet Dry 80-400Best AssortmentBMOTL Wet Dry 80-4009.6/10View on Amazon
  3. 3Dura-Gold 240 RollBest Longboard RollDura-Gold 240 Roll9.6/10View on Amazon
  4. 4Fandeli 120-2500Best Wide RangeFandeli 120-25009.6/10View on Amazon

A fender with peeling paint sits on the bench, and the paint has to come off before primer goes on. The wrong paper either leaves paint behind or cuts into the metal, so the grit and the backing matter as much as the elbow grease. This guide compares the best sandpaper to remove paint across five sheets and rolls, from coarse stripping grits to fine finishing grits, so the surface is ready for primer.

GarageToolHQ earns a commission when you buy through links on this page, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall Virginia Abrasives 80: 80 grit aluminum oxide in a 20 sheet pack, built for aggressive paint removal and surface leveling. Check price on Amazon
  • Best Assortment BMOTL Wet Dry 80-400: 80 to 400 grit in 12 sheets, silicon carbide, wet or dry, for stripping then smoothing. Check price on Amazon
  • Best Longboard Roll Dura-Gold 240 Roll: 240 grit, 2-3/4 in wide and 12 yards long, hook and loop for air file sanders. Check price on Amazon
  • Best Wide Range Fandeli 120-2500: 36 sheets from 120 to 2500 grit, silicon carbide, wet or dry. Check price on Amazon

Picks for the garage

Sandpaper Sheets General Purpose 80 Grit, Coarse

Sandpaper Sheets General Purpose 80 Grit, Coarse

Virginia Abrasives9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 80 grit aluminum oxide sandpaper in a pack of 20 sheets sized 9 x 11 in, stated for aggressive sanding, material removal and paint removal.

Pros

  • 80 grit aluminum oxide for aggressive paint removal
  • 20 sheets for a full stripping job
  • C weight backing resists tearing
  • Cuts to fit sanding blocks and hand sanders

Cons

  • Only 80 grit in the pack
  • Wet sanding is not stated
  • No hook and loop backing for sander pads
  • No storage case, only resealable packaging
BMOTL Wet Dry Sandpaper Sheets 9x11

BMOTL Wet Dry Sandpaper Sheets 9x11

BMOTL9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A wet or dry silicon carbide assortment from 80 to 400 grit in 12 sheets sized 9 x 11 in, stated for stripping coatings and preparing surfaces for priming.

Pros

  • 80 to 400 grit range covers stripping to smoothing
  • Silicon carbide abrasive on latex paper backing
  • Wet or dry use
  • 12 sheets cut to quarter, third or half size

Cons

  • Only 2 sheets of each grit
  • Finest grit is 400, so final polishing needs finer paper
  • No hook and loop backing for machine sanders
  • No warranty term is stated
Dura-Gold 240 Grit Gold Longboard Sandpaper

Dura-Gold 240 Grit Gold Longboard Sandpaper

Dura-Gold9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A continuous roll of 240 grit aluminum oxide corundum, 2-3/4 in wide and 12 yards long, with a hook and loop backing for air file and longboard sanders.

Pros

  • 240 grit for feather edging and paint removal
  • 12 yard roll trims to any length
  • Hook and loop backing fits air file sanders
  • Aluminum oxide corundum for a sharp cut

Cons

  • Only 240 grit in the roll
  • Needs a longboard sander or block with a hook and loop shoe
  • No sheet variety for finer finishing
  • No warranty term is stated
Fandeli | Waterproof Sandpaper

Fandeli | Waterproof Sandpaper

Fandeli9.6/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A waterproof silicon carbide assortment from 120 to 2500 grit in 36 sheets sized 22.86 x 9.14 cm, stated for car polishing, wood furniture sanding and metal sanding.

Pros

  • 36 sheets from 120 to 2500 grit
  • Silicon carbide for wet work
  • Water-resistant backing for wet or dry use
  • Grit printed on the back of each sheet

Cons

  • Coarsest grit is 120, so heavy stripping is slow
  • Sheets are smaller than the 9 x 11 in sheets in this guide
  • No hook and loop backing for sander pads
  • Grit counts vary by sheet, with 3 or 4 sheets per grit
3M Wetordry Sandpaper 03006, 3 2/3 x 9 in, 5 Pack

3M Wetordry Sandpaper 03006, 3 2/3 x 9 in, 5 Pack

3M9.5/10 Shop Score
i
The Shop Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A wet or dry silicon carbide assortment from 1000 to 2500 grit in 25 sheets sized 3 2/3 x 9 in, stated for polishing clear coat and sanding out paint defects.

Pros

  • 1000 to 2500 grit for clear coat polishing
  • Waterproof backing for wet or dry use
  • Self-fracturing silicon carbide stays sharp
  • Maker claims a 10% smoother finish than conventional 3M sandpaper

Cons

  • Fine grits only, 1000 to 2500, so it cannot strip paint
  • Small 3 2/3 x 9 in sheets
  • No coarse grit for material removal
  • Sheets are sized for handwork and machine pads, not longboard sanders

Other tools worth a look

Compared on paper

Model Shop Score Grit range Sheets Sheet size Abrasive Backing Wet or dry
Virginia Abrasives 80 9.6/10 80 20 sheets 9 x 11 in Aluminum oxide C weight paper Not stated
BMOTL Wet Dry 80-400 9.6/10 80 to 400 12 sheets 9 x 11 in Silicon carbide Latex paper Wet and dry
Dura-Gold 240 Roll 9.6/10 240 12 yards 2-3/4 in wide Aluminum oxide corundum Hook and loop Not stated
Fandeli 120-2500 9.6/10 120 to 2500 36 sheets 22.86 x 9.14 cm Silicon carbide Water-resistant paper Wet and dry
3M Wetordry 03006 9.5/10 1000 to 2500 25 sheets 3 2/3 x 9 in Silicon carbide Waterproof A-weight paper Wet and dry

Grit, sheet size and backing are manufacturer stated, as published on each listing and collected 18 November 2026.

How the picks were scored

Each pick is scored on performance, build, value, safety and warranty, with safety points only for stated safety features or certifications and warranty points only for a stated warranty term. No pick in this guide states a safety certification or a warranty term, so those two parts score zero across the board.

Product Shop Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Virginia Abrasives 80 9.6 30 21 21 n/a 0
BMOTL Wet Dry 80-400 9.6 29 21 21 n/a 0
Dura-Gold 240 Roll 9.6 30 20 20 n/a 0
Fandeli 120-2500 9.6 28 20 21 n/a 0
3M Wetordry 03006 9.5 27 21 19 n/a 0

No score drops under 9.2 or climbs past 9.8; a tool’s place inside those bounds is set by its weighted point total. Only powered tools, or tools with stated safety features, get safety points. Everything else is rated out of 90.

What the listings tell you

Five sandpaper listings were read for this guide. All five state grit and sheet size, and three state wet or dry use. Two state a hook and loop or latex backing, and one states a resealable pack. None states a warranty term or a safety certification.

Buying guide: best sandpaper to remove paint

Start coarse, then step up

Paint removal starts with a coarse grit. The 80 grit sheets in this guide are stated for aggressive sanding, material removal and surface leveling, while 240 grit is stated for feather edging and shaping body filler. After the paint is off, step up through finer grits so the surface is smooth enough for primer.

Sheets, rolls and blocks

Sheets sized 9 x 11 in cut to fit a sanding block or a hand sander, and the 12 yard roll trims to any length for a longboard or air file sander. A hook and loop backing holds the paper on a sander shoe, while plain sheets fold for handwork around curves.

Wet or dry

Wet sanding keeps grit from clogging and cools the working surface, according to the maker of the wet or dry sheets here. Dry sanding cuts with speed. Use wet passes where the listing states wet use, and keep the paper dry where it does not.

After the paint is off

Fine grits from 1000 to 2500 are stated for polishing clear coat and sanding out paint defects, not for stripping. Keep a fine pack on hand for the finish work that follows the stripping, and check the sandpaper grit guide before choosing a grit for each pass.

When the surface is ready for primer, the best paint gun for automotive picks cover the next step.

Air tool safety

Wear eye protection with every air tool, use impact-rated sockets on impact wrenches, disconnect the air line before changing accessories, and finish lug nuts with a torque wrench to the vehicle's spec. See OSHA eye and face protection. Read our Safety Disclaimer.

Garage Fit Check

  • Sheets are 9 x 11 in and cut to fit a sanding block; check the block size before ordering.
  • The 12 yard roll needs a longboard sander or block with a hook and loop shoe.
  • Wet sanding needs water nearby and a surface that can get wet.
  • Keep sheets in the resealable pack between jobs so they stay organized and clean.
  • Check the grit printed on the back of each sheet before starting a pass.

FAQ: garage tools

What grit sandpaper removes paint?

Coarse grits do the heavy work. The 80 grit sheets in this guide are stated for aggressive sanding and material removal, while 240 grit is stated for feather edging. Start coarse, then step up through finer grits for the finish.

Can paint be sanded off wet or dry?

Both, where the listing states it. The wet or dry sheets here work either way, with wet passes keeping grit from clogging and cooling the surface. Where a listing does not state wet use, use the paper dry.

Is a sanding block needed?

A block keeps the paper flat and the pressure even. The 9 x 11 in sheets here cut to fit a sanding block, and the roll fits longboard file boards and hand sanding blocks with a hook and loop shoe.

What grit comes after the paint is off?

Step up through finer grits before primer. The packs here run from 80 to 2500 grit, and the fine grits from 1000 to 2500 are stated for polishing clear coat and sanding out paint defects.

Can fine grit sandpaper remove paint?

Not well. Fine grits from 1000 to 2500 are stated for polishing and defect removal, not stripping. Use a coarse grit for removal and save the fine sheets for the finish.

Related: the sandpaper grit chart, how to use sandpaper, how to clean sandpaper, the best sandpaper for metal rust, the best sandpaper sponge, the best dual action polisher, the types of electric sanders and the air tools hub.

More buying guides