How to Clean Rusty Drill Bits Quickly and Safely
Brush the rust off the flutes with a wire brush, wipe the bit clean, dry it fully, and store it dry so the rust stays off.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VASTOOLS 15pcs Wire Brushes Set9.6/10View on Amazon - 2
WENORA 10 Pcs Wire Brush for Drill9.6/10View on Amazon - 3
ValueMax 8PC Wire Brush Set with Beechwood Handle9.6/10View on Amazon - 4
6 Pieces Wire Brushes Set9.5/10View on Amazon
You reach for a drill bit and find rust on the flutes, so here is how to clean rusty drill bits: brush the loose rust off with a wire brush, wipe the bit clean, dry it fully, and store it dry so the rust does not come straight back. A drill-mounted wire wheel clears a badly rusted bit, while a hand brush suits a bit you only need to touch up.
GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.
Below: surface rust or a bit past saving, the step-by-step clean, and the wire brush sets that do the job.
| # | Product | Shop Score | Buy |
|---|---|---|---|
| 1 | VASTOOLS 15pcs Wire Brushes Set | 9.6/10 | Buy on Amazon |
| 2 | WENORA 10 Pcs Wire Brush for Drill | 9.6/10 | Buy on Amazon |
| 3 | ValueMax 8PC Wire Brush Set with Beechwood Handle | 9.6/10 | Buy on Amazon |
| 4 | 6 Pieces Wire Brushes Set | 9.5/10 | Buy on Amazon |

VASTOOLS 15pcs Wire Brushes Set
A 15-piece wire brush set with 1/4-inch hex shank drill brushes rated to 4500 RPM, stainless steel hand brushes, and scrapers.
Pros
- 15 pieces: drill brushes and hand brushes in one set
- Drill brushes rated to 4500 RPM
- Offset handles keep knuckles clear
- 3/64-inch thick scraper edges resist curling
Cons
- No nylon brush for gentle cleaning
- No brass brush for surfaces that scratch easily
- No warranty term is stated
- No storage case in the box

WENORA 10 Pcs Wire Brush for Drill
A 10-piece set of carbon steel drill brushes with a 1/4-inch hex shank, rated to 4500 RPM, for rust removal and paint stripping.
Pros
- 10 pieces: pen, wheel, and cup brushes
- Rated to 4500 RPM for fast rust removal
- 1-inch pen brushes reach tight spaces
- 1/4-inch hex shank for a stable fit
Cons
- No hand brush for work away from a drill
- No nylon or brass brush for gentle cleaning
- No warranty term is stated
- No larger cup brush for broad surfaces

ValueMax 8PC Wire Brush Set with Beechwood Handle
An 8-piece hand brush set with brass, stainless steel, and nylon bristles on beechwood handles, for rust, dirt, and paint cleaning.
Pros
- Three bristle types: brass, stainless steel, and nylon
- 10-inch scratch brushes with 3 x 16 rows of bristles
- Curved beechwood handles for grip
- Nylon brushes for gentle cleaning
Cons
- No drill attachment, so all work is by hand
- No cup or wheel brush for heavy rust
- No scraper for caked-on dirt
- Fewer pieces than the 15-piece VASTOOLS set

6 Pieces Wire Brushes Set
A hand brush set of 6 brushes with brass, nylon, and stainless steel bristles, mini heads for narrow gaps, and 2 cleaning scrapers.
Pros
- Three bristle types: brass, nylon, and stainless steel
- Mini brush heads clean narrow gaps
- 2 cleaning scrapers included
- Hanging hole for vertical storage
Cons
- No drill attachment, so all work is by hand
- No cup or wheel brush for heavy rust
- Shorter than the 10-inch ValueMax scratch brushes
- 6 pieces, the smallest set here
How to clean rusty drill bits step by step
- Knock the loose rust off first. Hold the bit over a bench and brush along the flutes, working from the shank toward the tip and following the twist of the flutes. A stiff steel brush clears flaking rust, and a brass or nylon brush gives a gentler final pass.
- Brush with the flutes, not across them. Follow the twist of the flutes so the wires reach into the grooves. For a badly rusted bit, mount a wire wheel or cup brush in a drill and let the spinning brush do the passes, with the bit clamped in a vise.
- Wipe the bit clean. Wipe the loosened rust and dust off with a dry rag, then a rag that is only slightly damp, and look at the cutting edges for pitting.
- Dry it fully. Leave the bit out on a dry rag until every trace of damp is gone. A bit put away damp rusts again.
- Store it dry. Keep clean bits in a dry drawer or case, away from damp garage corners, and wipe a bit down after use in wet material.
Wear eye protection when you brush a bit, and keep gloves off while a brush spins in a drill, since a glove can catch on the wires. Wire brushes shed bristles, and a spinning wire wheel throws them farther than a hand brush.
Surface rust or a bit past saving
Light rust sits on the surface and brushes off to reveal clean steel underneath. If the cutting edges are pitted or chipped after brushing, the bit will not cut cleanly again. A twist bit with a pitted or chipped tip belongs in the scrap bin, while a bit that only carries surface rust goes back in the drawer.
Drill-mounted or hand brush?
Drill-mounted brushes spin in your drill and clear heavy rust in fewer passes, while hand brushes give you control on small bits and tight spots.
| Set | Brush kinds | Shank or handle |
|---|---|---|
| VASTOOLS 15-Pc Brush Set | Cup, wheel, end, hand brushes, scrapers | 1/4-inch hex shank, 4500 RPM |
| WENORA 10-Pc Brush Set | Pen, wheel, and cup brushes | 1/4-inch hex shank, 4500 RPM |
| ValueMax 8-Pc Brush Set | Brass, stainless steel, and nylon hand brushes | Beechwood handles, 7- and 10-inch brushes |
| Jikvmis 6-Pc Brush Set | Brass, nylon, stainless steel hand brushes, scrapers | 7-inch brushes, hanging hole |
The wire brush sets for this job
The sets below cover the two ways to clean a bit: drill-mounted wheels and cups for heavy rust, and hand brushes for touch-ups.
Read the manual before first use, wear eye protection, keep the work area clear and ventilated, and stay within every stated rating. Read our Safety Disclaimer.
FAQ: garage tools
Can I clean rusty drill bits with a wire brush?
Yes. A steel wire brush clears surface rust from the flutes, and a drill-mounted wheel or cup brush from the WENORA or VASTOOLS sets, rated to 4500 RPM, clears heavy rust faster. Brush along the flutes, wipe the bit clean, and dry it fully.
Should I use a drill-mounted brush or a hand brush?
Use a drill-mounted brush for heavy rust and a hand brush for light touch-ups. The WENORA and VASTOOLS sets mount in a drill on a 1/4-inch hex shank, while the ValueMax and Jikvmis sets are hand brushes.
How do I keep drill bits from rusting again?
Dry each bit fully after cleaning and store it in a dry drawer or case. Wipe a bit down after use in wet material.
Can a rusty drill bit be saved?
A bit with surface rust can be saved by brushing the flutes clean. A bit whose cutting edges are pitted or chipped after brushing will not cut cleanly again.
What brush should I use on a drill bit?
Use a steel wire brush for heavy rust and a brass or nylon brush for a gentler pass. The ValueMax and Jikvmis sets have brass, stainless steel, and nylon brushes, and the WENORA and VASTOOLS sets use carbon steel drill brushes.
Related: how to clean rusty drill bits, the best rust remover for metal, and the best drill bit to drill through metal.




