Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Step Drill Bit Sizes: Chart and Range

Step drill bit sizes run from 1/8 inch to 1-3/8 inch across the sets in this guide, with a bit covering many hole sizes in steps.

Step Drill Bit Sizes: Chart and Range
On this page

You are adding a switch to a steel panel on the workbench and the hole has to fit the switch body, not the nearest twist bit in the drawer. Step drill bit sizes are the hole sizes marked as steps along a cone-shaped bit, so a bit drills many hole sizes. You pick the step that matches the hole you need, drill to that step, and stop.

As an Amazon Associate I earn from qualifying purchases. GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.

Below: how the steps on a bit work, the size ranges the sets in this guide cover, and how to pick the step that matches the hole you need.

Step drill bit sizes: how the steps work

A step drill bit is a cone with a flat step at each size. THINKWORK, Bestwork and Klein Tools mark the sizes on the bit, so you can read the step you are drilling to. NEIKO lists a 13-step bit with sizes from 1/8 inch to 1/2 inch, and a 12-step bit with sizes from 3/16 inch to 7/8 inch. THINKWORK and Bestwork list a bit with 19 steps that runs from 3/16 inch to 1-3/8 inch. Each step cuts the hole to its own size, and the NEIKO and SS SHOVAN listings state that their bits deburr the edge as they cut.

  • Cone shape. The bit widens step by step, and each step is a hole size.
  • Marked steps. Size marks on the THINKWORK, Bestwork and Klein Tools bits show the size of each step.
  • A bit covers many sizes. A 13-step bit from NEIKO covers sizes from 1/8 inch to 1/2 inch.
  • Clean edge. The NEIKO spiral grooved design deburrs chips and debris, and the SS SHOVAN bits deburr and chamfer as they cut.

Common step drill bit size ranges

The sets in this guide cover different ranges. A small set starts at 1/8 inch and stops at 3/4 inch or 7/8 inch, while a larger set runs from 1/8 inch to 1-3/8 inch. A bit on its own can also cover a wide range: the Klein Tools bit runs from 7/8 inch to 1-3/8 inch. Use the chart below to match a set to the largest hole you need.

Set Range Step sizes listed
NEIKO 10181A, 3-piece 1/8 to 7/8 inch 31
NEIKO 10173A, 5-piece 1/8 to 1-3/8 inch 50
THINKWORK, 5-piece 1/8 to 1-3/8 inch 59
Bestwork, 5-piece 1/8 to 1-3/8 inch 59
FRITZFURT, 3-piece 1/8 to 3/4 inch 29
EZARC M35, 3-piece 1/8 to 7/8 inch Not stated
SS SHOVAN M35, 3-piece 1/4 to 7/8 inch Not stated
Klein Tools KTSB15 7/8 to 1-3/8 inch Not stated

Read the range as the smallest and largest holes the set can drill. If the largest hole you need sits above the top of the range, the set cannot drill it, so pick a set whose top step reaches your hole size. The 13-step NEIKO bit lists each size from 1/8 inch to 1/2 inch, so check the list on the bit before you drill.

How to pick a step drill bit size

  1. Measure the hole you need. Match the hole to a step the bit lists, not to a size between steps.
  2. Check the range. The set has to reach the largest hole in the job: the NEIKO 10173A set runs to 1-3/8 inch, while the FRITZFURT set stops at 3/4 inch.
  3. Check the shank. Most sets here use a 1/4-inch hex shank, and the Klein Tools bit uses a 3/8-Inch hex shank, so the shank has to fit your drill chuck.
  4. Check the thickness limit. The EZARC set suits metal sheet up to 1/8 inch thick and stainless steel sheet up to 1 mm thick, so check your stock thickness against the limit the maker states.
  5. Add cutting oil on metal. EZARC calls for cutting oil or coolant before use, SS SHOVAN calls for cutting oil or water during use, and FRITZFURT calls for cutting oil on stainless steel.
  6. Check impact use. EZARC warns against impact mode, since it may break the shank, while the NEIKO and FRITZFURT listings state their bits fit impact drivers, so follow the maker of the bit you hold.
Watch the thickness limit

The EZARC set suits metal sheet up to 1/8 inch thick and stainless steel up to 1 mm thick. Past that limit the bit is past the thickness the maker states it suits, so check the thickness of your stock before you drill.

Garage safety

Read the manual before first use, wear eye protection, keep the work area clear and ventilated, and stay within every stated rating. Read our Safety Disclaimer.

Step drill bit sizes vs twist drill bits

A twist bit drills a hole of a set size, so a job with many hole sizes needs a full set of twist bits. A step bit covers many sizes on a cone: the NEIKO 10181A set lists 31 step sizes across 3 bits, and the THINKWORK set lists 59 steps across 5 bits. The trade is thickness: the sets in this guide are stated for sheet metal and thin stock, and the EZARC set states a limit of 1/8 inch on metal sheet. The NEIKO and SS SHOVAN listings state that their bits deburr the hole as they cut.

  • Sizes per bit. Steps in the sets in this guide run from 1/8 inch to 1-3/8 inch, and the 19-step bit in the THINKWORK and Bestwork sets runs from 3/16 inch to 1-3/8 inch.
  • Material. The sets in this guide cover sheet metal, stainless steel, aluminum, copper, wood and plastic.
  • Shank. Most sets here use a 1/4-inch hex shank, and the Klein Tools bit uses a 3/8-Inch hex shank.
  • Finish. The NEIKO spiral grooved design deburrs chips and debris for smooth cutting, and the SS SHOVAN bits deburr and chamfer.

For more on where a step bit works well, see the guide to step drill bit uses and the picks for the best drill bit to drill through metal. For choosing bits in general, see drill bit tips.

Coatings and hardness

The size range decides the holes a bit can drill. The coating and the steel decide how long the edge holds up in metal, so it pays to know what the names on the box mean.

  • Titanium nitride. The NEIKO sets use industrial high-speed steel with a titanium nitride coating.
  • M35 cobalt steel. The EZARC, SS SHOVAN and FRITZFURT sets use M35 cobalt high-speed steel, with about 5% cobalt in the SS SHOVAN and FRITZFURT sets.
  • AlTiN coating. The EZARC coating is rated at 89HRC, and the Klein Tools bit uses an AlTiN coating.
  • Hardness. The Bestwork set states Rockwell 62-65 hardness.
  • Flute angle. The FRITZFURT set states a 25 to 28 degree spiral flute angle.
  • Tip angle. The SS SHOVAN set states a 118 degree X-type opening design.
  • Gauge. The Klein Tools bit states it cuts 16-Gauge steel.

Coatings and steel grades do not change the sizes a bit drills. Pick the size range first, then the coating that matches the metal you drill most.

FAQ: garage tools

What is the smallest step drill bit size?

The smallest step in the sets in this guide is 1/8 inch. The NEIKO, EZARC, THINKWORK, Bestwork and FRITZFURT sets all start at 1/8 inch.

What is the largest step drill bit size?

The largest step in the sets in this guide is 1-3/8 inch, on the NEIKO 10173A set, the THINKWORK set, the Bestwork set and the Klein Tools bit. The FRITZFURT set stops at 3/4 inch, so check the top step before you buy.

How many hole sizes does a step drill bit set cover?

It depends on the set. The NEIKO 10181A set lists 31 step sizes, the NEIKO 10173A set lists 50, the THINKWORK and Bestwork sets list 59, and the FRITZFURT set lists 29 hole sizes.

Can a step drill bit drill stainless steel?

Yes. The EZARC set suits stainless steel sheet up to 1 mm thick, and the SS SHOVAN set suits stainless steel under 1 mm. The NEIKO, THINKWORK, Bestwork and FRITZFURT sets also list stainless steel. Add cutting oil, as the EZARC, SS SHOVAN and FRITZFURT makers advise.

What shank size do step drill bits use?

Most sets in this guide use a 1/4-inch hex shank. The Klein Tools bit uses a 3/8-Inch hex shank, and the THINKWORK and Bestwork sets list a 1/4-inch and a 3/8-Inch shank.

Related: step drill bit uses, the best drill bits for stainless steel, the cordless tools hub and the best drill bits for metal and steel.

More buying guides