Large Size Tap and Die Set: Sizes Explained
The large sets in this guide cover bigger threads than a standard set, with SAE sizes from 1/4 inch to 1 inch and metric sizes from M6 to M24.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
GEARWRENCH 114 Piece Ratcheting Tap and Die Set9.4/10View on Amazon - 2
toolant 127-Piece Metric & SAE Ratcheting Tap and Die Set9.6/10View on Amazon
A bolt hole with stripped threads stops a brake job cold: the caliper bracket bolt will not hold, and drilling a new hole is not the answer. A large size tap and die set is the kit that cuts or restores those bigger threads, with taps for holes and dies for rods and bolts. This guide explains what counts as large, how the sizes read, and how to pick a set for the job.
Other tools worth a look
GEARWRENCH 114 Piece Ratcheting Tap and Die SetCheck price on Amazon
Kolvoii 52-Piece Large SAE Tap and Die SetCheck price on Amazon
ABN Large Tap and Die Set StandardCheck price on Amazon
IRWIN Tap And Die SetCheck price on Amazon
toolant 45-Piece SAE Tap and Die SetCheck price on Amazon
GEARWRENCH 42 Piece Ratcheting Tap & Die SetCheck price on Amazon
GarageToolHQ earns a commission when you buy through links on our product pages, at no extra cost to you. Read our affiliate disclosure.
Below: what counts as a large set, how SAE and metric sizes read, and how to use a set without breaking a tap.
What a large size tap and die set covers
“Large” describes the top end of the size range, not the piece count. The large sets here run SAE sizes from 1/4 inch to 1 inch and metric sizes from M6 to M24: the EFFICERE 45-piece SAE large set reaches 1 inch and its metric large set reaches M24, the KJE 52-piece jumbo sets do the same, and the VEVOR 51-piece SAE set also runs 1/4 inch to 1 inch. A standard set stops lower: the EFFICERE 86-piece master set runs SAE sizes from number 4 to 5/8 inch and metric sizes from M3 to M16. The GEARWRENCH 114-piece (on Amazon) set runs SAE sizes from 4-40 to 3/4 inch and metric sizes from 3 mm to 18 mm, so it sits between a standard set and a large one.
Piece count alone does not make a set large: a 114-piece set can top out at 3/4 inch while a 45-piece large set reaches 1 inch. Read the size range on the box before the piece count.
SAE sizes, coarse and fine
SAE sizes read as diameter in inches followed by threads per inch: 1/4-20 means a 1/4 inch diameter with 20 threads per inch, and 1-8 means a 1 inch diameter with 8. Coarse threads (UNC) have fewer threads per inch than fine threads (UNF) at the same diameter. The EFFICERE 45-piece SAE large set carries both, with 20 coarse and 20 fine taps and dies:
| Size | Coarse (UNC) | Fine (UNF) |
|---|---|---|
| 1/4 | 1/4-20 | 1/4-28 |
| 5/16 | 5/16-18 | 5/16-24 |
| 3/8 | 3/8-16 | 3/8-24 |
| 7/16 | 7/16-14 | 7/16-20 |
| 1/2 | 1/2-13 | 1/2-20 |
| 9/16 | 9/16-12 | 9/16-18 |
| 5/8 | 5/8-11 | 5/8-18 |
| 3/4 | 3/4-10 | 3/4-16 |
| 7/8 | 7/8-9 | 7/8-14 |
| 1 | 1-8 | 1-14 |
Pipe threads use a different mark: the EFFICERE 86-piece master set includes a 1/8x27NPT tap for pipe threads, where NPT marks a tapered pipe thread rather than a straight bolt thread.
Metric sizes, coarse and fine
Metric sizes read as a diameter in millimeters followed by the pitch in millimeters: M10x1.5 means a 10 mm diameter with a 1.5 mm pitch, and M24x3.0 means 24 mm with a 3.0 mm pitch. As with SAE, coarse means a wider pitch and fine means a narrower pitch at the same diameter. The EFFICERE 45-piece metric large set carries both, with 20 coarse and 20 fine taps and dies:
| Size | Coarse | Fine |
|---|---|---|
| M6 | M6x1.0 | M6x0.75 |
| M8 | M8x1.25 | M8x1.0 |
| M10 | M10x1.5 | M10x1.25 |
| M12 | M12x1.75 | M12x1.5 |
| M14 | M14x2.0 | M14x1.5 |
| M16 | M16x2.0 | M16x1.5 |
| M18 | M18x2.5 | M18x1.5 |
| M20 | M20x2.5 | M20x1.5 |
| M22 | M22x2.5 | M22x1.5 |
| M24 | M24x3.0 | M24x1.5 |
The KJE 52-piece metric jumbo set covers the same span, M6x0.75 to M24x3.0, with 20 taps and 20 dies.
Taps and dies: which one cuts what
A tap cuts internal threads inside a drilled hole. A die cuts external threads on a rod or a bolt. That one difference decides which tool to pick up: a stripped hole needs a tap, and a damaged bolt shank needs a die. Both tools cut by turning them into the work with a handle, and both need the matching size and pitch or the thread will not fit.
Dies come in two shapes. Hex dies fit a wrench or a socket, which gives leverage in tight spaces and makes them handy for chasing an old thread without removing the part. Round dies need a die stock to turn them. The EFFICERE 86-piece set uses hex dies and includes large and small tap handles, a T-type tap handle, and large and small die stocks. Ratcheting T-handles wind a die with a 5° swing arc and a reversing lever, so the handle does not need a full turn in a tight spot; the GEARWRENCH 114-piece set and the toolant 127-piece (on Amazon) set both use them.
Tapered teeth start a thread more easily. The EFFICERE large sets note tapered teeth on their taps and dies, and the VEVOR 116-piece (on Amazon) set notes tapered teeth on its tapping tools. A pitch gauge identifies the thread before cutting: the EFFICERE 86-piece set includes 2 thread pitch gauges, and the KJE large SAE set and the Kolvoii large (on Amazon) set each include an SAE pitch gauge, and the KJE large metric set includes a metric pitch gauge.
How to use a large tap and die set
Work in order and let the tool cut at its own pace:
- Identify the thread. Match the pitch gauge to the old thread or the mating fastener and read the size and pitch first: see how to use a thread gauge.
- Pick the matching tap or die. Same size, same pitch, same system: an SAE tap does not cut a metric thread. Check the manual for the drill size when tapping a new hole.
- Oil the cut. Use a suitable cutting oil on the tap or die and the work. It keeps the teeth cutting instead of tearing.
- Start straight and turn by hand. Keep the tap square to the hole and the die square to the rod. Turn forward a little, then back off to break the chip, and keep going until the thread is cut through.
- Clear the chips and check the fit. Brush the chips away and thread the mating fastener in by hand; it should turn in without force.
- Deal with a broken bolt. The KJE and Kolvoii large sets include spiral flute extractors for broken fasteners, covering 3 to 18 mm. See the best broken bolt extractor guide for the full method.
Severely stripped holes may need another repair method, and a tap will not save a hole that has lost too much metal. When the thread is gone, a thread repair kit is the next step: see the thread repair kit for oil pan and bolt thread repair kit guides.
What to look for in a large set
Material and hardness decide how long the cutting edges last. The EFFICERE large sets use GCr15 bearing steel hardened to Rockwell 60 HRC, and the KJE jumbo sets use GCr15 bearing steel hardened to over 60 HRC. The EFFICERE 86-piece master set uses high speed steel with a titanium coating, and the VEVOR 51-piece set uses bearing steel heat treated at 1472°F / 800°C. The VEVOR 116-piece set uses bearing steel hardened to HRC56 with an 800°C heat treatment.
Count the accessories, not just the taps and dies. The EFFICERE 86-piece set comes with a large tap handle, a small tap handle, a T-type tap handle, a large die stock, a small die stock, 2 thread pitch gauges, a slotted screwdriver and a metal storage case. The VEVOR 51-piece set adds an adjustable wrench, a T-handle tap wrench, an adjustable die stock, a spiral flute extractor, an automatic center punch and a flat-head screwdriver. The toolant 127-piece set states a 180-day term for its accessories and a 1-year term for its main tool body.
Storage matters in a crowded garage. The KJE and Kolvoii large sets pack into a blow-molded case, the EFFICERE 86-piece set packs into a metal case, and the VEVOR 51-piece set comes in a case with organized compartments. Check the case size before buying: the EFFICERE 86-piece case measures 14.9 by 10.9 by 2.2 inches. The VEVOR 51-piece set is listed at 13.49 pounds.
Read the manual before first use, wear eye protection, keep the work area clear and ventilated, and stay within every stated rating. Read our Safety Disclaimer.
FAQ: garage tools
What is the largest size in a large tap and die set?
The large sets here run to 1 inch SAE and M24 metric: the EFFICERE 45-piece sets and the KJE 52-piece jumbo sets reach those sizes across their SAE and metric versions.
Do large tap and die sets include coarse and fine threads?
Yes. The EFFICERE 45-piece large sets include 20 coarse and 20 fine taps and dies in each system, so each diameter comes in a coarse pitch and a fine pitch.
What is the difference between a tap and a die?
A tap cuts internal threads inside a hole, and a die cuts external threads on a rod or a bolt. Pick the tap for a stripped hole and the die for a damaged bolt shank.
Can a tap and die set fix a stripped thread?
A tap can chase or re-cut a lightly damaged thread, and a die can do the same on a bolt or a rod. Severely stripped holes may need another repair method, so check the thread before cutting.
What size tap and die set do I need for truck work?
Match the set to the fasteners on the truck: the large sets here cover 1/4 inch to 1 inch SAE and M6 to M24 metric.
Related: tap and die size chart, best drill and tap set, best thread pitch gauge, bolt extractor size chart, and the engine and shop equipment guides.




